In order to improve the strength of concrete structures, the fiber reinforcement of concrete has become an essential factor. This study was conducted as an experimental program to gain a better understanding of how the variance of fiber shape and type affect the structural performance of solid and hollow reinforced concrete beams using four types of fiber (hooked-end, straight, corrugated steel fiber, and polyolefin fiber) under torsion. For this purpose, ten fiber-reinforced concrete beam specimens, five solid and five hollow, with square cross sections were fabricated using the adopted types of fiber. The role of fiber type in the improvement of the mechanical properties of hardened concrete was also investigated. The results revealed that the mechanical properties of the hardened concrete mix was enhanced by using the existing fiber in concrete, and the higher improvement was shown in the splitting tensile strength test and modulus of rapture in specimens with corrugated steel fiber. The torsional behavior of solid and hollow beams was improved significantly, and the capacity of torsional strength was especially improved for the beams strengthened with corrugated steel fiber. Straight and polyolefin fiber showed a slight improvement in the concrete mechanical properties and less enhancement in the torsional capacity of the tested beams. However, the tested beams reinforced by polyolefin fiber provide better ductility under torsion compared with the use of other types of fiber.
Built-up steel girders have many applications in structural engineering, both in bridges and buildings. Flat web steel girders, which are the traditional choice, involve several weaknesses. Girders with corrugated webs were found to be more effective in their load-carrying capacity and deflection than girders with flat webs. In light of this, an effort is made in this work to examine how the addition of triangular corrugated webs influences the load-bearing capacity and deflection of steel girders. This study aimed to determine whether or not the strength of built-up steel with corrugated webs could be improved. A concentrated midspan load was applied to six simply supported steel beams of varying span-to-depth ratios (1.0, 1.833, and 2.5) and web corrugation amplitudes (30 and 60 mm). An increase in ultimate strength of 15.7% to 35.1% was found for webs with triangular corrugations of 30 mm and from 2% to 29.1% for webs with corrugations of 60 mm. A reduction in deflection of up to 35.3% can be attained when using triangular corrugated webs. It was also found that using webs with 30 mm corrugations was more efficient than using webs with 60 mm corrugations. The effect of corrugation was found to fade when the span-to-depth ratio increased to 2.5. This led to the conclusion that using webs of 30 mm amplitude of triangular corrugation could improve the strength and serviceability of steel girders. Doi: 10.28991/CEJ-2023-09-02-09 Full Text: PDF
This paper consists of experimental study on ability of use of wire mish strengthening and steel fiber to recover the flexural strength of the slab after configuring openings cut out with different shapes. 15 slabs (800*800*95 mm) made of high strength concrete were prepared and tested, these slabs were divided to gropes, the first group was with square openings, the second group with was rectangular openings. For each group, two different strengthening techniques were used wire mish (with different layers and widths) strips around openings and steel fibers (with four contents of 0, 0.5, 1.0 and 1% by volume fraction). The results showed that the two strengthening techniques increased the load-carrying capacities of the slabs with openings compared with the slabs without strengthening. The wire mish was more effective than the steel fibers technique. Wire mish and steel fiber reduced the cracks at the inside faces of opening and also wire mish prevent it at the inside corners.
This study examined eight specimens of two groups of deep beam (DB) with the same dimensions and reinforcement quantity, where the first group had four specimens tested under two-point loads and the second group had four specimens tested under one-point load (Ammash HK, AL-Mousawi MM. Experimental investigation of deep beam reinforced with different types of reinforcement. Eng Technol Appl Sci Res. 2021;11(2):7585–90.) where both groups have the same reinforcement and the dimensions and difference between the groups was only the type of load. Digital image correlation technology software was used to verify the results. Upon examining the results, each group had one reference specimen with conventional reinforcement and the other three specimens were with strut reinforcement. It was observed that the strut reinforcement technique was more effective than the conventional reinforcement. This study also found that the load capacity was decreased at two-point loads from one-point load. The results from the present study were compared to those from a prior study (Ammash HK, AL-Mousawi MM. Experimental investigation of deep beam reinforced with different types of reinforcement. Eng Technol Appl Sci Res. 2021;11(2):7585–90.) that only employed a one-point load. The concrete type, its dimensions, and its method of reinforcing were the same as Ammash and AL-Mousawi’s (Experimental investigation of deep beam reinforced with different types of reinforcement. Eng Technol Appl Sci Res. 2021;11(2):7585–90.) study. The maximum load capacity for SC (Reference DB specimen) and S10 (the deep strut beam employed a specimen with 100% reinforcement from the reinforced web) specimens for one-point load were more tolerant to stress than the two-point loads, with 15% for SC and 27% for S10 as both specimens had comparable amounts of reinforcement. When a force is applied that is less than the sum of the two load points, cracks occur in the shear and flexural zones at one load point. We have found that the use of two-point loads leads to a decrease in the maximum load capacity of specimens when compared with a one-point load. It was also noted that cracks are formed in the shear and flexural zones at one-point load when a load less than the two-point load is applied. It was also observed that when two-point loads were applied to a specimen, the displacement was less than half of what it was when tested under a one-point load, and the strain in specimens examined under two-point load was lower than in specimens examined under one point load.