This study investigated the use of self-compacting concrete (SCC) made with recycled coarse aggregates (RCAs), which represents a trend of producing environment-friendly concrete, integrated with hot-rolled steel sections by means of headed stud shear connectors in composite structures. Therefore, thirty-six push-out test specimens were examined to assess the shear strength and behavior of the headed stud connectors embedded in RCA-SCC, with the concrete compressive strength, stud diameter, and RCA ratio as the main variables. Four ratios of RCAs ranging from 0 to 60% were used to produce concrete with three different compressive strengths (25, 33, and 40 MPa) for each one. It was found that the use of SCC with RCAs had a negative effect on the shear strength of headed stud connectors. This negative effect could be reduced by increasing the concrete compressive strength and/or the stud diameter. Similarly, a reduction in the shear stiffness of the tested specimens was inversely proportional to the RCA ratio, while the ultimate slip was directly proportional to the RCA ratio. An evaluation of the test results was made by comparing them with those determined by Eurocode 4 and AASHTO LRFD.
The bond strength of tension lap splices in recycled-coarse-aggregate-reinforced concrete strengthened with hybrid (steel–polyolefin) fibers was experimentally investigated. This study was conducted with the help of twelve lap-spliced beam specimens. The replacement level of coarse natural aggregates with recycled concrete aggregate (RCA) was 100%. The following variables were investigated: various ranges of steel–polyolefin fibers—100–0%, 75–25%, 50–50%, 25–75%, and 0–100%—in which the total volume fraction of fibers () remains constant at 1%; and two lengths of lap splices for rebars of 16 mm diameter (): 10 and 15 . The test results showed that the best range of steel–polyolefin fibers that gave the highest bond strength was 50–50%. The ductility of the fiber-reinforced recycled-aggregate (FR-RA) concrete was significantly improved for all the cases of various relative ratios of steel and polyolefin fibers. The bond strength was also predicted using three empirical equations proposed by Orangun et al., Darwin et al., and Harajli. This study showed that the Harajli equation gave a more accurate estimation of the bond strength of reinforcing bars embedded in FR-RA concrete than those proposed by Orangun et al. and Darwin et al.
In order to improve the strength of concrete structures, the fiber reinforcement of concrete has become an essential factor. This study was conducted as an experimental program to gain a better understanding of how the variance of fiber shape and type affect the structural performance of solid and hollow reinforced concrete beams using four types of fiber (hooked-end, straight, corrugated steel fiber, and polyolefin fiber) under torsion. For this purpose, ten fiber-reinforced concrete beam specimens, five solid and five hollow, with square cross sections were fabricated using the adopted types of fiber. The role of fiber type in the improvement of the mechanical properties of hardened concrete was also investigated. The results revealed that the mechanical properties of the hardened concrete mix was enhanced by using the existing fiber in concrete, and the higher improvement was shown in the splitting tensile strength test and modulus of rapture in specimens with corrugated steel fiber. The torsional behavior of solid and hollow beams was improved significantly, and the capacity of torsional strength was especially improved for the beams strengthened with corrugated steel fiber. Straight and polyolefin fiber showed a slight improvement in the concrete mechanical properties and less enhancement in the torsional capacity of the tested beams. However, the tested beams reinforced by polyolefin fiber provide better ductility under torsion compared with the use of other types of fiber.
Strength enhancement of non-seismic concrete beam–column joints (NSCBCJs) via carbon fiber-reinforced polymer composites (CFRPCs) integration has become a viable strategy. However, the implementation of these NSCBCJs without transverse reinforcement shows poor performance during earthquakes in seismic locations. Thus, strengthening the anti-seismic performance of NSCBCJs to meet the acceptance criteria of ACI 374.1-05 is fundamentally significant. Yet, in addition to limited experimental results, only a few numerical studies based on the finite element model have been performed to determine the anti-seismic behavior of NSCBCJs. Consequently, the stress contribution of CFRPCs to NSCBCJs is not clearly understood. Therefore, we used a finite element model to examine the strength contribution of CFRPCs to NSCBCJs. The performance of the proposed finite element model was validated using the experimental results, demonstrating a good agreement between them. It was shown that the strength of NSCBCJs was improved due to CFRPC incorporation, thereby achieving compliance with the seismic requirements of ACI 374.1-05. In addition, CFRPCs presence could enhance the confinement, reduce the deformation of the NSCBCJs and, thus, decrease their stiffness and strength degradation, while simultaneously improving the energy dissipation.
21 December 2017 in Journal of University of Babylon for Engineering Sciences
This experimental work along with an analyticalanalysis is investigated.The behavior of simply supported steel beams with lightweight and normal concrete slab that have the same compressive strengthand slump was studied. Eight specimens tested under mid-point load and analysis by plastic analysis theory. Four of composite beams havea steel I-section beam with normal concreteslab and the other four with lightweight concrete slab. Different degrees of shear interaction were considered (100% to 40%). It was observed that there are no essential differences between the modes of failure that appeared in the tested composite beams with normal and lightweight concrete. Also, it was notedthat there is a decrease in the initial stiffness and also in the ultimate strength of the composite beams when the concrete of the flanges for the tested specimens was replaced from normal to lightweight concrete for different degrees of shear connections.The analytical results for all tested beam specimens, except that with normal concrete and 100% degree of shear interaction, gave overestimate results compared with those of experimental results.
The effect of macro synthetic polyolefin fibers on the bond strength of tension lap splices in reinforced concrete (RC) beams is investigated in this study. The bond between the reinforcement and concrete plays a vital role in the strength of RC beams. The presence of polyolefin fibers in the lap splice zone confines the concrete and enhances the bond strength of the steel bars. The use of synthetic fibers is preferable to steel ones since steel suffers from corrosion over time. Tests were conducted on 12 full-scale beam specimens to determine the effect of fiber volume fraction (Vf), bar diameter (db) and concrete cover-to-bar diameter (c/db) on the response. Four volume fractions (Vf = 0, 0.5, 1 and 1.5%) of polyolefin fibers and three bar sizes (db = 16, 20 and 25 mm) with the corresponding (c/db = 2.31, 1.75 and 1.30) were considered to evaluate the bond strength. The test results demonstrated that the polyolefin fibers noticeably enhanced the bond strength and ductility of spliced tension bars. Experimental results were compared with those obtained from two theoretical methods including ACI Committee 318 design provisions. The results showed that the equation proposed by the ACI Committee overestimates the bond strength.