In this paper, the authors examined the technology to maximize the use of renewable energy. Passive ventilation systems are expected to reduce the energy consumption of the fan and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, this paper presents a “passive ventilation system with a solar air heater” that combines a passive ventilation system with the solar air heater to preheat the air. This system can reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then the system was implemented in a real building for verification. The simulation performs hourly unsteady calculations, allowing for accurate evaluation of the annual simulation. Based on the measurement results, the effects of heating load reduction and prediction methods are presented. The solar air heater reduced the monthly ventilation load by up to 50% or more, and by at least 15%. It was also confirmed that there was a high correlation between the actual measurements and the simulation results.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

Since the Japanese Building Standards Act was revised in 2000, the installation of steel timber connectors (STCs) to reinforce timber frame (TF) connections has been mandated for new-build TF houses in Japan. However, for the TF houses built before then, more than 40% do not have sufficient STCs and are considered earthquake-prone. This study proposed a simple and easy seismic retrofit technique for such earthquake-prone existing houses. The proposed technique can reinforce TF connections using only plywood and common nails and achieve equivalent performance to the benchmark STCs used in Japanese TF houses, such as the “CP-T type” or the combination of “VP type” and “BP type” STCs. Experiments were performed to compare the proposed technique with the STCs using pullout and full-scale in-plane cyclic tests. The experimental results showed that the proposed technique had a higher seismic performance than the STCs, which was particularly excellent in displacement ductility to prevent a collapse of the TF house without damaging the timbers. The proposed technique will be accepted by many carpenters when retrofitting earthquake-prone existing houses because simple and easy.

Improvements in envelope performance have reduced heat loss from insulation, and the ratio of heat loss through ventilation load has become relatively large. In recent years, the use of heat recovery ventilation systems (HRV) has particularly increased. However, ventilation generates not only ventilation load but also air conveying fan power, such that conserving energy for both is important. Therefore, this paper focuses on a passive ventilation system with a solar air heater (PVSAH), which is a passive ventilation system that does not use air conveying fan power and uses a solar air heater that uses solar energy. The total energy consumption of the PVSAH, the widely used mechanical exhaust ventilation system (EV), and the HRV, which has high energy efficiency, was compared with the ventilation load plus air conveying fan power. The primary energy evaluation and carbon dioxide (CO₂) emissions were compared by region, and the optimal system was proposed according to regional characteristics. In warmer zones, the PVSAH saved the most energy, while the HRV increased energy consumption. The comparison of CO₂ emissions by ventilation systems when using heat pumps for cooling and heating showed that PVSAH > MEV > HRV for Heating Degree-Day (HDD) 1500 and below, PVSAH > HRV > MEV for HDD 1500 to 2750, and HRV > PVSAH > MEV for HDD 2750 and above. MEV were favored in that order. As the CO₂ emission factor decreases, the difference in CO₂ emissions between systems decreases. If the difference in emissions becomes smaller, then considering the initial and running costs and the risk of failure of the system is crucial. A simple system configuration with low risks of failure and maintenance, such as PVSAH, may prove advantageous in the future.

We have clarified that external insulation reduces the probability of reinforcement corrosion in reinforced concrete buildings in cold snowy districts by 45–78%. Renovation of external insulation is one of the effective methods for improving the insulation performance and durability of reinforced concrete buildings, but there are almost no data that demonstrate durability. Therefore, the carbonation depth and the cover depth were investigated for six medium-rise-wall type reinforced concrete buildings in Hokkaido, Japan, which had been refurbished for external insulation. As a result, it was clarified that the external insulation suppressed the carbonation depth by 30% or more, even when the bonding method of the external insulation was different. In addition, it was clarified that the external insulation further suppressed carbonation in walls where the carbonation depth tended to increase in snowy cold districts. Specifically, external insulation reduced carbonation by up to 35% on surfaces that tend to dry out due to sunlight, and by 49% on surfaces that are affected by water that deteriorates the concrete surface layer.