Loizos Efthymiou

Mr. Loizos Efthymiou


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 March 2017 in Applied Physics Letters
Verified
Journal Article
Closed access
LELoizos Efthymiou
Loizos Efthymiou
GLG. Longobardi
G. Longobardi
GCG. Camuso
G. Camuso
TCT. Chien
T. Chien
MCM. Chen
M. Chen
FUF. Udrea
F. Udrea
In this study, an investigation is undertaken to determine the effect of gate design parameters on the on-state characteristics (threshold voltage and gate turn-on voltage) of pGaN/AlGaN/GaN high electron mobility transistors (HEMTs). Design parameters considered are pGaN doping and gate metal work function. The analysis considers the effects of variations on these parameters using a TCAD model matched with experimental results. A better understanding of the underlying physics governing the operation of these devices is achieved with a view to enable better optimization of such gate designs.

28 June 2019 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
LELoizos Efthymiou
Loizos Efthymiou
KMKarthick Murukesan
Karthick Murukesan
GGiorgia Longobardi
Giorgia Longobardi
FUFlorin Udrea
Florin Udrea
ASAyman Shibib
Ayman Shibib
KTKyle Terrill
Kyle Terrill
In this letter we investigate by means of experimental results and TCAD simulations the threshold voltage instability due to off-state drain stress in p-GaN gate AlGaN/GaN-on-Si HEMTs. When the drain of the p-GaN HEMT is biased in the off-state the threshold voltage (Vth) shows a linear increase up to ∼ 40%. This increase saturates at drain bias voltages above 50V. The positive Vth shift is attributed to the ionization of acceptor traps in the AlGaN region below the p-GaN gate with the source of these trapping sites suggested to be the p-GaN gate out-diffused Mg dopant atoms. The ionization of the Mg acceptors due to high electric field during off-state bias and the removal of the generated holes from the AlGaN region through the gate contact creates the charge conditions for a positive Vth shift. The sharp decrease in the gate drain capacitance (Cgd) for VD < 50V, the simulated gate edge electric field reaching its peak for a drain voltage bias VD ∼ 50V and the positive threshold voltage shift observed for negative gate stress further validate the proposed model.

10 September 2021 in IEEE Journal of the Electron Devices Society
Verified
Journal Article
Open access
KMKarthick Murukesan
Karthick Murukesan
LELoizos Efthymiou
Loizos Efthymiou
FUFlorin Udrea
Florin Udrea
For large scale testability of p-GaN HEMTs it is essential to investigate threshold voltage (Vth) instability from the perspective of the measurement induced instability. In this paper the impact of accumulated gate bias stress during standard transfer characteristic measurements (ID-VG) in a p-GaN AlGaN/GaN-on-Si normally off HEMT is quantitatively analysed and modelled. This illustrates the associated threshold voltage (Vth) instabilities and leads to a better understanding of the Vth measurement challenges of a p-GaN HEMT. Upon an application of a constant gate bias close to nominal Vth the drain current ID shows an initial marginal rise, followed by a short stable period (IDstable-Tzone) and a steep decay period. The effective bias history built on the gate stack varies when pulse on-time (Ton) or step time (Tstep), corresponding to pulsed or DC step ID-VG measurements, are varied. We find that this can lead to a Vth variation of up to 20%. It is also observed that the choice of Ton and Tstep determines whether ID is measured in IDstable-Tzone or the rise or decay periods. Measurement induced Vth instability is attributed to trapping of 2DEG electrons at the AlGaN barrier and we demonstrate that an ohmic gate contact, in comparison to the Schottky gate contact, may compensate for the trapped 2DEG electrons by hole injection across the AlGaN barrier. Experimental results of Vth stability under the same stress conditions for a Schottky and ohmic gate contact are supported by a detailed TCAD analysis.

21 March 2017 in Energies
Verified
Journal Article
Open access
PDF file
LELoizos Efthymiou
Loizos Efthymiou
GCGianluca Camuso
Gianluca Camuso
GGiorgia Longobardi
Giorgia Longobardi
TCTerry Chien
Terry Chien
MCMax Chen
Max Chen
FUFlorin Udrea
Florin Udrea
With Gallium Nitride (GaN) device technology for power electronics applications being ramped up for volume production, an increasing amount of research is now focused on the performance of GaN power devices in circuits. In this study, an enhancement mode GaN high electron mobility transistor (HEMT) is switched in a clamped inductive switching configuration with the aim of investigating the source of oscillatory effects observed. These arise as a result of the increased switching speed capability of GaN devices compared to their silicon counterparts. The study identifies the two major mechanisms (Miller capacitance charge and parasitic common source inductance) that can lead to ringing behaviour during turn-off and considers the effect of temperature on the latter. Furthermore, the experimental results are backed by SPICE modelling to evaluate the contribution of different circuit components to oscillations. The study concludes with good design techniques that can suppress the effects discussed.

25 March 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
LELoizos Efthymiou
Loizos Efthymiou
GGiorgia Longobardi
Giorgia Longobardi
GCGianluca Camuso
Gianluca Camuso
FUFlorin Udrea
Florin Udrea
This paper investigates the advantages and disadvantages of bonding pad over active area (BPOA) layout over a conventional layout for lateral AlGaN/GaN HEMTs designed for use in power applications. Extensive analysis of the performance of a BPOA device, both experimentally and supported by 3-D TCAD model simulations, reveals that while it can offer a higher current capability per unit area, it can lead to other disadvantages compared to a conventional design when considering reliability aspects.