Electrical Resistance Tomography (ERT) offers a non-destructive evaluation (NDE) technique that takes advantage of the inherent electrical properties in carbon fiber reinforced polymer (CFRP) composites for internal damage characterization. This paper investigates a method of optimum selection of sensing configurations for delamination detection in thick cross-ply laminates using ERT. Reduction in the number of sensing locations and measurements is necessary to minimize hardware and computational effort. The present work explores the use of an effective independence (EI) measure originally proposed for sensor location optimization in experimental vibration modal analysis. The EI measure is used for selecting the minimum set of resistance measurements among all possible combinations resulting from selecting sensing electrode pairs. Singular Value Decomposition (SVD) is applied to obtain a spectral representation of the resistance measurements in the laminate for subsequent EI based reduction to take place. The electrical potential field in a CFRP laminate is calculated using finite element analysis (FEA) applied on models for two different laminate layouts considering a set of specified delamination sizes and locations with two different sensing arrangements. The effectiveness of the EI measure in eliminating redundant electrode pairs is demonstrated by performing inverse identification of damage using the full set and the reduced set of resistance measurements. This investigation shows that the EI measure is effective for optimally selecting the electrode pairs needed for resistance measurements in ERT based damage detection.
Internal damage in Carbon Fiber Reinforced Polymer (CFRP) composites modifies the internal electrical conductivity of the composite material. Electrical Resistance Tomography (ERT) is a non-destructive evaluation (NDE) technique that determines the extent of damage based on electrical conductivity changes. Implementation of ERT for damage identification in CFRP composites requires the optimal selection of the sensing sites for accurate results. This selection depends on the measuring scheme used. The present work uses an effective independence (EI) measure for selecting the minimum set of measurements for ERT damage identification using three measuring schemes: two-probe, four-probe and multi-probe. The electrical potential field in two CFRP laminate layups with 14 electrodes is calculated using finite element analyses (FEA) for a set of specified delamination damage cases. The measuring schemes consider the cases of 14 electrodes distributed on both sides and seven electrodes on only one side of the laminate for each layup. The effectiveness of EI reduction is demonstrated by comparing the inverse identification results of delamination cases for the full and the reduced sets using the measuring schemes and electrode sets. This work shows that the EI measure optimally reduces electrode and electrode combinations in ERT based damage identification for different measuring schemes.
11 March 2021 in Structural Control and Health Monitoring
Electrical resistance tomography (ERT) is a non‐destructive evaluation (NDE) technique that measures the voltages when electric current is injected in a body where damage induced electrical conductivity changes occur. Accurate and efficient damage identification in carbon fiber reinforced polymer (CFRP) composites using ERT requires the optimal selection of the sensing sites. The present work uses an effective independence (EI) measure for selecting the optimally reduced set of measurements among all possible for ERT damage identification. Finite element analyses (FEA) are used to calculate the electrical potential in two CFRP laminate layups with 14 electrodes given a set of specified delamination cases that span the space of possible damage states. Measurement reduction uses two strategies based on individual or group selection about the injection site. A third strategy performs complete electrode exclusion. Inverse identification of delamination cases for the full and the reduced sets after applying the strategies estimates the effectiveness of EI reduction. Results show the lowest errors come from individual measurement elimination. Electrode elimination is attainable with acceptable accuracy loss. This work shows that the EI measure optimally reduces electrode and electrode combinations in ERT‐based damage identification.
The electrical resistance tomography (ERT) is a non-destructive evaluation (NDE) technique that uses the inherent conductivity variations of composites to characterize internal damage. This article presents a study on the use of Kriging surrogate models for inverse identification of delamination in composites using ERT. Kriging surrogates are used to predict the change in electrical response of composites with delamination and matrix cracking damage. The results show that Kriging surrogates can successfully identify delamination even in the presence of matrix cracking. The technique demonstrated here that combines model order reduction with Kriging surrogates provides a computationally efficient and accurate method for damage identification using ERT.
9 February 2023 in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
As structures increase in complexity, in the use of high-performing materials and designs, their health assessment becomes increasingly challenging. Ultrasonic guided waves (UGWs) have shown to be very promising in the inspection of large (i.e. aerospace components) attenuating (i.e. composite materials) structures and have been successfully employed for damage detection in a variety of fields. The intrinsic complex nature of UGWs, due to their dispersive behavior, combined with the structural complexity of the applications, though, makes the interpretation of UGW inspections very challenging. Numerical simulations of UGW propagation become crucial to this end and have been addressed with fully numerical, semi-analytical and hybrid approaches. The capability of predicting UGW scattering can inform experimental testing in optimizing the sensitivity of UGW inspections to specific waveguides and defects, and in interpreting the acquired data for the non-destructive identification and quantification of damages. In this work, an improved computational tool for UGW scattering predictions is presented. The approach relies on the Global-Local method and leverages the efficiency of the semi-analytical finite element (SAFE) method and the parallelized implementation of the coupled solution. 2D applications of the Global-Local approach for UGW scattering predictions in composite structures over a wide range of frequencies will be presented, together with the demonstration of the improved computational performance. The computational efficiency promises feasible and reliable UGWs predictions in multi-layered complex assemblies and different damage scenarios, and enables virtual UGWs inspections and future integration in NDE testing.
8 April 2024 in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
The nondestructive characterization and monitoring of defects in composite structures by ultrasonic guided waves are hindered by the complexity of the interaction. Efficient computational modeling of propagating ultrasonic guided waves in waveguides with discontinuities is necessary to properly tune inspections and correctly interpret the scattering behavior. This paper studies the influence of different defect types in composite plates on ultrasonic guided wave scattering. Employing a hybrid global–local method, the energy spectra of transmitted and reflected waves in defected composite plates are numerically analyzed over a broad frequency range. Through parametric analyses of defect dimensions and locations, the resulting trends of the effect of specific defect features on the scattering behavior, as well as the importance of observing scattering on a broad frequency range, are accurately computed and highlighted. The presented findings indicate the potential for effective defect characterization and monitoring.