Deep roadway deformation due to soft rock, rock dip, and horizontal tectonic stress is uneven and asymmetrical primarily in large loose zones. Traditional anchor support is influenced by the yield strength and shear strength of the anchors and has a limited prestress capacity or shear resistance. When the roadway roof is laminated rock or when the roadway passes through layered rock or rock interfaces, interlayer sliding commonly occurs, which can easily lead to anchor cables being sheared off. The tape tunnel in the Zhengling Mine passes through several rock strata and requires anchors to achieve a high shear resistance and prestress. To solve these problems, an anchor cable and C-shaped tube that can bear lateral shear forces were developed, and a full-section anchor cable and C-shaped tube support system were created based on extruded arch theory. Numerical results from FLAC3D show that the new scheme effectively controls surface convergence and plastic zone extension. Field tests have demonstrated that the amount of surface displacement was at least 42 smaller in the new support scheme. The extruded arch formed by the highly prestressed anchor cable and concrete spray layer can effectively control the bulking load within the loose zone, and the ACC effectively resists interlayer shear.
The free section of prestressed anchor cable is a weak part of support. A new supporting structure named Anchor Cable and C‐Shaped Tube, which can bear transverse shear force, solves the problem that rock bolt and anchor cable are prone to shear failure in the free section and also solves the contradiction between high preload and low shear bearing capacity of support materials. Double‐shear tests of Anchor Cable and C‐Shaped Tube with smooth joint planes were carried out. Double‐shear tests were carried out on the anchor cables with the diameter of 21.6 mm and the same type of Anchor Cable and C‐Shaped Tube under different preload conditions. The influence of the preload on the shear performance of supporting materials and the enhancement effect of Anchor Cable and C‐Shaped Tube supporting structure on the shear performance of anchor cables were analyzed. The test results confirm that Anchor Cable and C‐Shaped Tube can improve the transverse shear resistance of the supporting material and increase the axial ultimate bearing capacity of the anchor cable during the shearing process. It is found that, during the double‐shear test, the fracture form of the supporting materials is tensile fracture, and when it is sheared, Anchor Cable and C‐Shaped Tube can reduce the stress concentration of the interaction between the joint surface and the surrounding rock and reduce the damage to the surrounding rock.
In view of the complex asymmetric deformation characteristics of inclined coal seam roadways and the tensed shear failure of anchor cable supports, the asymmetric support scheme of an anchor cable with a C-shaped tube is proposed. In order to study its supporting effect on an inclined coal seam roadway, this paper first explores the difference in shear performance between an anchor cable with a C-shaped tube and an anchor cable through double shear tests. Then, based on the asymmetric deformation characteristics of an inclined coal seam roadway in the Pangpangta Mine, a numerical simulation is used to study the asymmetric support effect of an anchor cable with a C-shaped tube in an inclined coal seam roadway. The results of the double shear test show that the anchor cable with the C-shaped tube has stronger resistance to shear load than that of the anchor cable. Through the results of the numerical simulation, the original stress field distribution on both sides of the roadway was found to be uneven due to the influence of the coal seam dip angle, and after the excavation of the inclined coal seam roadway, the displacement and plastic zone distribution on both sides showed obvious asymmetric characteristics. Compared with the symmetric support, the asymmetric support can obviously alleviate the asymmetric deformation characteristics of the two sides and effectively control the deformation and plastic failure zone of the roadway. The anchor cable with the C-shaped tube has better resistance to shear deformation than that of the anchor cable. The anchor cable with the C-shaped tube can reduce the deformation and plastic area of the roadway more effectively.
In order to deeply understand the influence of different factors on the characteristic indicators of the double‐row‐pipe partial horizontal frozen body in the sand‐gravel stratum under the effect of seepage flow, several sets of sand‐gravel stratum frozen model tests were carried out based on the similarity theory. The research showed that (1) under the effect of seepage flow, the backwater surface of the horizontal frozen body is in the shape of a quadratic parabolic and the development velocity of the backwater surface is inversely proportional to the square of the freezing time. The influence of seepage velocity on the downstream length and the freezing front development velocity of the backwater surface is stronger than the refrigerant temperature; (2) overlap time of the second row of frozen soil column increases with the increase of the distance between frozen pipes and seepage velocity and decreases with the decrease of the refrigerant temperature. The influence of various factors on the overlap time follows the order as the distance between freezing pipes > seepage velocity > refrigerant temperature. The average development velocity of the upstream surface decreases with the increase of the seepage velocity and the refrigerant temperature and first increases and then decreases with the increase of freezing pipe spacing. The influence of various factors on the average development velocity follows the order as seepage velocity > the distance between freezing pipes > refrigerant temperature. In addition, through the regression analysis, the quantitative relationship between the maximum arrangement spacing of the frozen pipes, the seepage velocity, and the refrigerant temperature was obtained. The research results can provide a basis for large‐area partial horizontal freezing construction in Beijing sand‐gravel stratum.
Based on the phenomenon of serious tensile-shear failure of bolts and cables, domestic and foreign scholars’ research on the mechanical properties of bolts and cables has gradually changed from pure tensile to tensile-shear performance. To reduce the long-term bolt and cable breakage accidents in deep soft rock tunnels in coal mines, we independently developed a new type of support material—anchor cable with C-shaped tube and a corresponding tensile-shear test system. The system parameters are set through theoretical derivation, and the three main structures of the test system are designed with ANSYS: shear box, vertical loading reaction frame, and horizontal loading reaction frame. The numerical simulation results show that when the thickness of the shear box steel plate is 20 mm, the maximum strain is about 2.7‰. When the diameters of the vertical column and the horizontal bar are 220 mm and 80 mm, respectively, the maximum strains of the column and the horizontal bar are about 0.17‰ and 0.04‰, respectively. The strength and deformation of the three main structures meet the design requirements. The developed test system was tested on-site. The test results show that the system can perform tensile test and two different modes of the double shear test. The main structure has no obvious deformation during the test, meeting the design requirements. In addition, the rational design of the shear box eliminates the error caused by the shear block. The results show that the shear resistance of anchor cable with C-shaped tube is better than that of pure anchor cables. The research results can provide a reference for developing other similar test systems.