Shear walls are one of the primary lateral resisting structural elements. Due to architectural and technical needs, openings in the structural wall are almost inevitable. Discontinuity regions and a reduction in wall stiffness result from these openings. The use of fiber-reinforced-polymer (FRP) systems is a sustainable construction solution for strengthening these areas and is a viable method to restore their integrity and serviceability. This paper presents an experimental and analytical study on the behavior of reinforced concrete (RC) shear walls with openings of various sizes and positions strengthened using glass-fiber-reinforced-polymer (GFRP) sheets. Ten RC shear walls were cast and tested; initially without strengthening; and then retested with a layer of bi-directional GFRP sheet added around the opening. The finite-element (FE) program ANSYS was used for modeling since using FE contributes to sustainability. The results showed that for un-strengthened walls with a 6.25% opening and strengthened walls with an 11.11% opening, the rate of stiffness degradation was reasonably low. As the opening size was enlarged, the strength and stiffness values were drastically reduced; and the shear walls with an opening at the mid-height position also have smaller load capacities compared to the bottom and top opening positions. In addition, the ability of the GFRP sheets to control stress redistribution and crack propagation improved the overall performance of the walls. The FE and experimental results match well. Furthermore, the ACI and ECP calculations revealed a good prediction of lateral load capacity without considering the opening position, whereas the other proposed models were inaccurate. Finally, the author proposed a reduction factor (β) to the shear strength equation provided by ECP-203-2020 depending on openings sizes and locations; and suggests that FRP sheets be used around openings to assure the appropriate performance and avoid unexpected failure.
With the rise in cement production required by conventional concrete, CO2 emissions increase, causing pollution to the atmosphere. Geopolymer concrete (GPC) is investigated in the literature as an eco-efficient alternative to conventional concrete (CC). However, most geopolymer studies focus on studying the mechanical properties of GPC, with only limited investigations on the structural performances of structural elements using GPC. The structural behaviors of GPC elements are yet to be completely understood, and there are no current studies on investigating the structural behaviors of geopolymer slag concrete. Thus, this paper investigates the flexural performances of reinforced geopolymer slag concrete beams, focusing on the effects of different beam depths and reinforcement ratios. Five full-scale ambient-cured reinforced geopolymer slag concrete beams were tested under four-point flexure, in addition to one control conventional concrete (CC) beam. The structural performances are evaluated, including the cracking moment, flexural capacity, load–deflection relationship, and crack distribution. The results indicate that the flexural behaviors of GPC beams are comparable to that of the CC beams. Compared to the CC beams, the GPC beams have 7.4% higher flexural moment capacity, 60% lower stiffness, 28% lower ductility, and 18.3% higher toughness. Finally, the Egyptian code of practice ECP 203 and ACI 318 are found to be applicable to safely design under-reinforced GPC flexural beam elements.
In this study, the Basalt fibers from basalt rocks are used to strengthen openings in deep beams where this fiber is an environmentally friendly material that doesn’t produce any toxic reactionswith air or water, and its surface is anti-explosion. Also, it doesn’t produce chemical reactionsthat may damage the environment or human health, when it contacts other chemicals, it is safe for use in industry and has no pollution, and the effect of strengthening deep beams withopenings vertically by using these basalt fiber sheets is studied. A practical program has been developed to study the behavior of deep beams strengthened with basalt fiber-reinforced polymer (BFRP) sheets. The practical program consists of 6 beams designed as American code, with various types of openings. The results of the tested sheets and results of beams such asdeflection, cracking load, crack propagation, ultimate load, and failure character, are recorded. Also, nonlinear analysis and mathematical equations are used in this study. This research can achieve that the basalt fiber sheets could affect slightly on the behavior of the deep beam with openings in cracking loads, deflections, stiffness, energy capacities, and ultimate loads