Junghwan Han

Prof. Junghwan Han

Chungnam National University, Daejeon, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2022 in IEEE Microwave and Wireless Technology Letters
Verified
Journal Article
Closed access
HAHyun Bae Ahn
Hyun Bae Ahn
HJHong-Gu Ji
Hong-Gu Ji
YCYunho Choi
Yunho Choi
SLSanghun Lee
Sanghun Lee
DKDong Min Kang
Dong Min Kang
JHJunghwan Han
Junghwan Han
This letter presents a gallium nitride (GaN) high electron mobility transistor (HEMT)-based three-stage low noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) that can apply to the fifth-generation (5G) new radio base station applications. The designed GaN-based LNA MMIC utilizes a hybrid-matching topology with double-shunt capacitors at input and output (I/O) matching networks to achieve broad return loss (RL) and bandwidth characteristics across 5G frequency range two bands. The design is fabricated in a 0.15 $\mu $ m GaN on silicon carbide technology and attains small signal gains greater than 21 dB, noise figures of 2.4–2.9 dB, 1-dB compression points greater than 19.1 dBm, output third-order intercept points greater than 28.5 dBm, and I/O RLs greater than 10 dB at 25–31 GHz band. The implemented design consumes a power of approximately 300 mW.

13 June 2014 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
KKKuduck Kwon
Kuduck Kwon
JHJunghwan Han
Junghwan Han
In this paper, a surface acoustic wave (SAW)-less receiver (RX) front-end adopting switchable front-end architecture has been presented for second-generation/third-generation/fourth-generation cellular applications. Depending on the RX-transmitter (TX) frequency separation, a favorable down-mixing architecture is selected between a current-sampling mixer and a voltage-sampling mixer. The proposed switchable architecture meets the specification of an input-referred second-order intercept point (IIP2) for the SAW-less RX while minimizing the power consumption. The implemented RX front-end consists of a wideband capacitor cross-coupled common-gate low-noise amplifier, a 25% duty-cycle passive mixer with IIP2 calibration circuitry, a baseband transconductor, and a trans-impedance amplifier. Fabricated in a 65-nm CMOS process, the SAW-less RX front-end provides conversion gain of 42 dB, and achieves noise figure of below 3.3 dB, out-of-band input-referred third-order intercept point of -2 dBm, and IIP2 of more than 56 dBm. It draws an average current of 14.8 mA from 1.2 V. The die area is 1.71 mm2.

10 November 2022 in IEEE Microwave and Wireless Technology Letters
Verified
Journal Article
Closed access
BBBeomsoo Bae
Beomsoo Bae
EKEunsoo Kim
Eunsoo Kim
SKSegyeong Kim
Segyeong Kim
JHJunghwan Han
Junghwan Han
This letter presents a dual-band complementary metal–oxide–semiconductor (CMOS) low-noise amplifier (LNA) for fifth-generation (5G) new radio (NR) frequency range 2 (FR2) applications. The proposed design utilizes a transformer-based band-switchable load to tune resonance conditions in the 26–30-and 37–40-GHz bands. Through on–off control of the transformer functionality, the primary inductance can be adjusted with lesser quality-factor ( $Q$ -factor) degradation compared to the conventional direct inductor switching approach. The proposed design is implemented using a 65-nm CMOS process. At 28 and 39 GHz, respectively, the gains of 13.7 and 13.1 dB, noise figures (NFs) of 3.8 and 4.1 dB, input 1-dB compression points of $-$ 15.2 and $-$ 16 dBm, and input third-order intercept points of $-$ 7.15 and $-$ 6.85 dBm are realized. The implemented design draws a bias current of 11.6 mA with a 1-V supply.

13 October 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
BBBeomsoo Bae
Beomsoo Bae
JHJunghwan Han
Junghwan Han
This brief presents a gain-boosted wideband complementary metal–oxide–semiconductor (CMOS) down-conversion mixer with body-effect control, which operates in a frequency range of 24–40 GHz. In the proposed design, the body voltage of mixer switches is adaptively controlled with respect to an applied local oscillator (LO) signal to enhance the switching capability. This technique improves the conversion gain (CG) and noise figure (NF) of the mixer without increasing LO signal power and current consumption. To validate the concept of the design, conventional and proposed mixers are implemented using a 65-nm CMOS process and their performance is compared. At an identical LO power of 5 dBm, the proposed wideband mixer demonstrates the CGs of 7.2 dB and 4.8 dB and NFs of 12.3 dB and 13.5 dB at 28 GHz and 39 GHz, respectively. Compared with the conventional mixer design, the CG and NF of the proposed mixer are improved by 2.2–3.3 dB and 1.2–2 dB in all operating frequency bands, respectively. The conventional and proposed mixers consume the identical die size of 0.87 mm ${\times }\,\,0.46$ mm and the power of 10.3 mW with the nominal supply of 1.0 V.

4 May 2021 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
PKPillseong Kang
Pillseong Kang
JHJunghwan Han
Junghwan Han
This article proposes a dual-band complementary metal-oxide-semiconductor (CMOS) radio frequency (RF) front end employing a hybrid transformer-based electrical-balance duplexer (EBD) and N-path filter embedded low-noise amplifier (LNA) for both in-band full duplexing (IBFD) and frequency-division duplexing (FDD) radios. To securely obtain sufficient self-interference cancellation (SIC) or transmitter (TX) leakage rejection in IBFD and FDD modes of the EBD at both low-band (LB) (0.7-1 GHz) and mid-band (MB) (1.8-2.2 GHz) frequency ranges, a band-switchable hybrid transformer is designed with a finely adjustable balance network to control the antenna impedance variations. In addition, the four-phase N-path LNA is utilized to further offer TX leakage rejection in the FDD operation. This RF front-end is fabricated using a 65-nm CMOS technology and is mainly characterized by long-term evolution frequency bands. The demonstrated design achieves SIC and TX leakage rejection greater than 55 dB for IBFD and FDD modes of all measured frequency bands, which has a maximum power handling capability of +25 dBm. Furthermore, the design attains voltage gains greater than 8.7 dB for LB and 3.7 dB for MB, noise figures of 10.4 dB for LB and 12.1 dB for MB, out-of-band (OB) P1dBs greater than +21.4 dBm for LB and +21.5 dBm for MB, and OB IIP3s greater than +39.7 dBm for LB and +43.1 dBm for MB. It draws a bias current of 23.8 mA from the LNA and output buffer with a nominal supply of 1.2 V and has an active area of approximately 2 mm 2 .

30 March 2022 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
BBBeomsoo Bae
Beomsoo Bae
JJJuhui Jeong
Juhui Jeong
SKSubin Kim
Subin Kim
JLJungwoo Lee
Jungwoo Lee
KKKuduck Kwon
Kuduck Kwon
JHJunghwan Han
Junghwan Han
This work presents a dual-band complementary metal–oxide–semiconductor (CMOS) up-conversion mixer that operates in the frequency range of 24.25–40 GHz. To realize highly linear characteristics at both the 28- and 39-GHz bands, the proposed design uses the single-stacked transistor configuration as well as band-switchable inductor and transformer loads. The up-conversion mixer comprises an intermediate frequency (IF) transconductance, a switching, and a radio frequency (RF) stage. Mixer switches are driven by three-stage local oscillator (LO) buffers. The design is fabricated in a 40-nm CMOS process and shows conversion gains exceeding 3.7 and 0.8 dB, output 1-dB compression points (OP1dBs) exceeding −1 and −0.2 dBm, and output 3rd-order intercept points (OIP3s) exceeding 9.2 and 3.8 dBm for 28 and 39 GHz bands, respectively. The implemented mixer consumes a bias current of 22.1 mA with a 1.1-V supply. The active area excluding bonding pads is 0.59 mm 2 .