30 March 2022 in IEEE Microwave and Wireless Components Letters
This work presents a dual-band complementary metal–oxide–semiconductor (CMOS) up-conversion mixer that operates in the frequency range of 24.25–40 GHz. To realize highly linear characteristics at both the 28- and 39-GHz bands, the proposed design uses the single-stacked transistor configuration as well as band-switchable inductor and transformer loads. The up-conversion mixer comprises an intermediate frequency (IF) transconductance, a switching, and a radio frequency (RF) stage. Mixer switches are driven by three-stage local oscillator (LO) buffers. The design is fabricated in a 40-nm CMOS process and shows conversion gains exceeding 3.7 and 0.8 dB, output 1-dB compression points (OP1dBs) exceeding −1 and −0.2 dBm, and output 3rd-order intercept points (OIP3s) exceeding 9.2 and 3.8 dBm for 28 and 39 GHz bands, respectively. The implemented mixer consumes a bias current of 22.1 mA with a 1.1-V supply. The active area excluding bonding pads is 0.59 mm 2 .
8 February 2023 in IEEE Microwave and Wireless Technology Letters
This letter presents a 28-GHz bidirectional amplifier that operates as a low-noise amplifier (LNA) and a drive amplifier in the receiver (RX) (forward) and transmitter (TX) (backward) modes, respectively. In the proposed design, the bidirectional operation is realized through supply switching (SS) by utilizing the symmetric structure of a complementary metal–oxide–semiconductor (CMOS) device. Additionally, the body voltage control of an n-type MOS (nMOS) device is applied to attain symmetric and enhanced performance in both the forward and backward operations. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band. It achieves a nearly identical performance in both the forward and backward modes.
20 January 2023 in IEEE Access
This study presents a broadband complementary metal-oxide semiconductor (CMOS) low noise amplifier (LNA), containing out-of-band (OB) blocker rejection capability without an additional calibration process. In the proposed design, separate all-pass and band-stop filter stages are provided in parallel as main and auxiliary paths, respectively, whose amplitude and phase variations are identically tracked by each other over a process, voltage, and temperature dependency. By appropriately combining an in-band signal and OB blockers passed through those filter blocks, robust OB blocker rejection can be realized in the wide frequency range. The designed LNA incorporates a pre-amplifier stage for broad input matching and low-noise characteristics, an N-path filter-based frequency selective stage, and a combiner stage to suppress undesired OB blockers. The designed calibration-free OB blocker rejection broadband LNA is fabricated in a 65 nm CMOS technology and mainly characterized in long-term evolution frequency division duplexing bands, ranging from 0.7 to 2.7 GHz. The demonstrated design consistently attains transmitter leakage and other OB blocker rejection of more than 22.8 dB and 16 dB in low-band (LB) (0.7-1 GHz) and mid- and high-band (MB and HB) (1.7-2.7 GHz) frequency range from several samples without extra gain or phase adjustment, respectively. The implemented LNA also achieves gains of 10.5-11.0 dB and 8-10 dB, noise figures of 3.7-4.1 dB and 3.8-4.9 dB, OB third-order intercept points greater than 8.2 dBm and 9.8 dBm, and OB 1-dB compression points greater than -5.2 dBm and -5.5 dBm, for LB and MB/HB, respectively. The implemented design consumes a total bias current of 23.9 mA with a nominal supply of 1.2 V and occupies an active area of 0.53 mm 2 , excluding bonding pads.
14 April 2025 in IEEE Microwave and Wireless Technology Letters
This work presents a 28-GHz complementary metal-oxide-semiconductor (CMOS) bidirectional mixer for frequency conversion in both receiver (RX) (forward) and transmitter (TX) (backward) modes. The design utilizes the symmetric source-drain structure of CMOS devices, with a supply-switching technique for bidirectional operation. Body-effect control and gain-boosting techniques are also applied to enhance performance in both modes. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band.
18 February 2025 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a cryogenic complementary metal-oxide-semiconductor (CMOS) active mixer designed to achieve low-noise and low-power characteristics at cryogenic temperatures. The proposed design employs a transformer-based current-bleeding (CB) technique that further enhances both the conversion gain and noise performance of the mixer when compared to the conventional CB approaches. Implemented as a double-balanced active mixer, the design was fabricated using a 65-nm CMOS process and validated across the 4-8 GHz frequency range under both cryogenic and room temperatures.
30 April 2024 in IEEE Access
This study proposes a broadband complementary metal-oxide semiconductor (CMOS) low-noise amplifier (LNA) with intrinsic band-selective out-of-band (OB) blocker rejection capabilities. The proposed LNA design utilizes a differential four-phase N-path filter as the amplifier load to offer a substantial total load impedance difference between the in-band (IB) and OB frequency bands. This ensures that the LNA design securely accomplishes a high-quality-factor frequency selectivity response with lower radio frequency signal losses and its OB rejection performance is maintained against process, voltage, and temperature variations, compared with the case of using the N-path filter as a signal path. To validate its blocker-tolerable performance, the designed LNA was fabricated using a 65-nm CMOS technology and was primarily characterized in the frequency division duplexing bands of the long-term evolution and fifth-generation new radio standards, spanning from 1.7 to 2.7 GHz. The implemented design consistently achieved a transmitter leakage rejection greater than 17 dB across all target frequency bands from several samples. Furthermore, the design attained IB voltage gains greater than 36.4 dB and 40.4 dB, noise figures (NFs) of 1.78 dB and 1.5 dB, OB input 1-dB compression point greater than –27.0 dBm and –26.7 dBm, and full-/half-duplexing OB input-referred third-order intercept points greater than 4.1/3.8 dBm and 4.8/5.0 dBm at the mid- and high-bands, respectively. The OB-induced NF degradation was maintained at less than 0.7 dB. A total bias current of 37.7 mA was required with a nominal supply voltage of 1.2 V. The occupied active area of the implemented design was approximately 0.77 mm2, excluding the bonding pads and input/output cells.