Kuduck Kwon

Kuduck Kwon

Auto-generated profile, based on publicly available information

Kuduck Kwon

Department of Electronics Engineering and the Department of BIT Medical Convergence, Kangwon National University, Chuncheon, South Korea

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
SKSinyoung Kim
Sinyoung Kim
KKKuduck Kwon
Kuduck Kwon
A new noise-cancelling method that employs a modified current-bleeding (CBLD) technique and balanced loads is presented by developing a design for a low-noise and high-linearity balun-low-noise amplifier (LNA) for broadband applications. The basic common-gate (CG)-common-source (CS) balun topology cannot achieve a noise figure (NF) of less than 3 dB. Thus, a practical topology containing a CS transistor of which the transconductance is N times larger than that of the CG transistor and a CS resistor of which the resistance is $N$ times smaller than that of the CG resistor is often used to decrease the NF. However, unsymmetrical load resistors cause a gain and phase imbalance at the differential output. The proposed modified CBLD technique enables the balun-LNA to achieve differential balanced output, low noise, and low-second-order distortion characteristics. The proposed balun-LNA is implemented in 65-nm CMOS technology and covers the frequency range of 50 MHz-1 GHz. It achieves a voltage gain of 30 dB, an S11 of less than -10 dB, an OIP3 of 25.9 dBm, and an OIP2 of 50.6 dBm. The minimum NF is 2.3 dB whereas the average NF is 2.63 dB across the whole band. It operates at a nominal supply voltage of 2.2 V with bias currents of 9 mA. The active die area is 0.0448 mm².

13 August 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
SKSinyoung Kim
Sinyoung Kim
KKKuduck Kwon
Kuduck Kwon
A new low-voltage and low-power noise-cancelling method that employs the local feedback g m -boosting and balanced loads is proposed by developing a design for a low-noise and low-power balun-low-noise amplifier (LNA) for low-power broadband applications. A common-gate (CG) - common-source (CS) balun-LNA with a modified current-bleeding (CBLD) technique has low noise performance and differential balanced output but consumes more power. Because local feedback boosts the overall g m of the CG stage using the amount of loop gain, the current consumption and supply voltage requirements can be mitigated. In addition, the cross-coupled cascode stage acts as a differential current balancer to improve the gain and phase mismatches at the differential output. Implemented in a 65-nm CMOS technology, the balun-LNA achieves a noise figure of 2.3 - 3 dB, a maximum voltage gain of 27.5 dB and a S 11 of less -10 dB over the frequency range of 50 MHz to 1.3 GHz. The measured OIP3 and OIP2 are 25.3 dBm and 45.3 dBm, respectively. It consumes 5.7 mA from a nominal supply voltage of 1 V while the active die area is 0.046 mm 2 .

30 September 2018 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
KKKuduck Kwon
Kuduck Kwon
SKSinyoung Kim
Sinyoung Kim
KSKi Yong Son
Ki Yong Son
A hybrid transformer-based CMOS tunable duplexer with a single-ended blocker-tolerant low-noise amplifier (LNA) is proposed for a highly integrated reconfigurable RF front-end architecture. The proposed LNA adopts Q-enhanced LC notch filter at the source of the cascode device and LC bandpass filter at the load. It improves the blocker tolerance and linearity of the receiver by rejecting unwanted out-of-band blockers and transmitter (TX) leakage signals. The duplexer with the notch-filtered LNA was fabricated in a 65-nm CMOS process. It has a voltage gain of 24.2 dB from the antenna to the LNA output with 28-dB notch filtering, cascaded noise figure of 6.4 dB, TX insertion loss of 3.8 dB, and IIP3FD of 52.4 dBm. It can also cover a mid-band range from 1.6 to 2.2 GHz in cellular applications. It draws an average current of 8 mA from a supply voltage of 1.2 V and has an active area of 1.19 mm 2 .

10 December 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
BPBeomyu Park
Beomyu Park
KKKuduck Kwon
Kuduck Kwon
In this article, a 2.4-GHz Bluetooth low-energy (BLE) receiver employing a new quadrature low-noise amplifier (LNA) is presented for low-power low-voltage Internet of Things (IoT) applications. The proposed quadrature LNA consists of a common-source (CS) amplifier with inductive degeneration, an active-type poly-phase filter (PPF), and an LC tank. The proposed active-type PPF between the CS amplifier and the LC tank provides quadrature generation, and the CS amplifier determines and optimizes the overall LNA performance parameters. Moreover, the proposed active-type PPF shares the dc bias current with the CS amplifier, thereby eliminating the necessity for additional current consumption. The implemented BLE receiver is composed of the quadrature LNA, a Gₘ-stage, a double-balanced current-mode passive mixer, a transimpedance amplifier, and an active-RC complex bandpass filter. The proposed design was fabricated in a 65-nm CMOS process and mainly characterized in the BLE operating frequency bands. The receiver achieves a noise figure of 8.2 dB, a conversion gain of 49.5 dB, an image rejection ratio of more than 33 dB, and an IIP3 of -25.75 dBm. The active die area of the implemented receiver is 1.16 mm², and it draws a bias current of 2.7 mA from a nominal supply voltage of 0.8 V.

28 December 2021 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
DSDonguk Shin
Donguk Shin
KLKyudo Lee
Kyudo Lee
KKKuduck Kwon
Kuduck Kwon
In this article, a blocker-tolerant receiver (RX) front end employing a dual-band $N$ -path balun low-noise amplifier (balun-LNA) is presented for advanced cellular applications. The proposed RX front end can achieve a superior input-referred second-order intercept point (IIP2) performance without any IIP2 calibration, as the $N$ -path balun-LNA performs RF bandpass filtering and enhances blocker tolerance as well as the overall linearity of the RX. The proposed band-switchable differential inductor with a center tap enables the LC tank of the balun-LNA to support the operation of both low-band (LB) and mid-band (MB) frequencies for 5G new radio (NR) sub-6-GHz cellular applications. The RX front end is comprised of the dual-band $N$ -path balun-LNA, a $G_{m}$ -stage, current-mode passive mixers with a 25% duty-cycle local oscillator signal, current-mode passive RC low-pass filters, and transimpedance amplifiers. The RX front end was fabricated through a 65-nm CMOS process, and it was characterized primarily in the 5G NR LB and MB frequencies. The active die area was 2.24 mm 2 , and the RX front end drew a bias current of 15.1 mA from a nominal supply voltage of 1 V. It achieved a noise figure of 4.5 dB, a conversion gain of 43.5 dB, an out-of-band input-referred third-order intercept point of 7.89 dBm, and an IIP2 of more than 55 dBm.

30 March 2022 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
BBBeomsoo Bae
Beomsoo Bae
JJJuhui Jeong
Juhui Jeong
SKSubin Kim
Subin Kim
JLJungwoo Lee
Jungwoo Lee
KKKuduck Kwon
Kuduck Kwon
JHJunghwan Han
Junghwan Han
This work presents a dual-band complementary metal–oxide–semiconductor (CMOS) up-conversion mixer that operates in the frequency range of 24.25–40 GHz. To realize highly linear characteristics at both the 28- and 39-GHz bands, the proposed design uses the single-stacked transistor configuration as well as band-switchable inductor and transformer loads. The up-conversion mixer comprises an intermediate frequency (IF) transconductance, a switching, and a radio frequency (RF) stage. Mixer switches are driven by three-stage local oscillator (LO) buffers. The design is fabricated in a 40-nm CMOS process and shows conversion gains exceeding 3.7 and 0.8 dB, output 1-dB compression points (OP1dBs) exceeding −1 and −0.2 dBm, and output 3rd-order intercept points (OIP3s) exceeding 9.2 and 3.8 dBm for 28 and 39 GHz bands, respectively. The implemented mixer consumes a bias current of 22.1 mA with a 1.1-V supply. The active area excluding bonding pads is 0.59 mm 2 .