Low temperature processed, metal-oxide free planar perovskite solar cells (PSCs) were fabricated using polyetherimide (PEI) modified poly(3,4-ethylenedioxylenethiophene):poly(styrene sulfonate) (PEDOT:PSS) as the cathode.
In this work, we used poly(3,4-ethylenedioxylenethiophene):poly(styrene sulfonate) (PEDOT:PSS, PH 1000) and poly(bis(4-phenyl)(2,4,6-trimethylphenyl)amine) (PTAA) as anode and hole transport materials, respectively, for fabricating metal oxide-free inverted perovskite solar cells (PSCs). The sheet resistance of the PEDOT:PSS (PH 1000) anode was reduced to 76 Ω sq−1 after treatment with ethylene glycol and phosphoric acid, a level comparable to that of conventional indium tin oxide. The hydrophobicity of PTAA improved the perovskite crystallization, facilitating performance improvements in the PSCs. A high power conversion efficiency (PCE) of 14.23% was achieved for these structured rigid PSCs on a rigid glass substrate, with the short-circuit current density, open-circuit voltage, and fill factor of 19.88 mA cm−2, 1.02 V, and 70.2%, respectively. Flexible PSCs on a polyethylene terephthalate substrate exhibited a high PCE of 10.51% with excellent bendability. Our results indicate that using anodes of PEDOT:PSS (PH 1000) and hole transport layers of PTAA presents a promising fabrication method for high-performance rigid and flexible metal oxide-free PSCs, which suggests future large-scale and roll-to-roll production.
Researching planar heterojunction perovskite solar cells has become increasingly popular in view of pursuing both a better photovoltaic performance and enhanced environmental stability. Recently, the use of integrated hole transport layers (HTLs) has attracted much attention because of the improvements in power conversion efficiencies (PCEs). However, previous research studies usually focused on the HTLs in regular-type devices, which do not affect the formation of perovskite crystals. Here, we developed the HTL for inverted solar cells, which integrated organic poly[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b]-dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl] (PTB7) with poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). PTB7 is used to tune the energy alignment and hydrophobicity of PEDOT:PSS to improve the hole transportation and perovskite formation. The integrated HTL (PEDOT:PSS/PTB7) demonstrated an enhanced hole extraction performance in perovskite solar cells due to better matched energy alignment. Furthermore, the hydrophobic nature of PTB7 provides a non-wetting surface that is beneficial to the crystal formation of perovskite, resulting in higher quality perovskite crystals. Using this simple process, the developed group exhibited a PCE of 18.43%, which was 16.5% higher than that of the reference devices (15.82%). In addition, due to the moisture-blocking characteristics of PTB7, the long-term stability of the devices was also obviously enhanced under ambient air conditions (25 °C) without encapsulation.
In this study, we introduced alcohol based vapor annealing of a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) layer for fabricating high-performance inverted perovskite solar cells. Atomic force microscopy measurements and atomistic theoretical simulations indicated that phase separation between PEDOT and PSS was enhanced by this annealing, improving the hole conductivity at the PEDOT:PSS layer. As a result of using methanol, the short-circuit current density improved from 20.7 to 21.6 mA cm−2; consequently, the power conversion efficiency (PCE) improved from 16.1 to 17.3%. However, using ethanol or isopropanol yielded a smaller performance improvement. The PCEs of the best sample in this study under forward and reverse scans were 17.7 and 18.0%, respectively, indicating that the PSC had a small hysteresis. Our results suggest that alcohol vapor annealing is a simple and effective method of developing high-performance inverted perovskite solar cells.