In order to obtain the calibration law of rock macro and meso parameters under three-dimensional conditions, based on the parallel bond model, starting with the basic theory of PFC and the qualitative relationship between macro and meso parameters, an orthogonal experimental scheme is designed. An improved BP algorithm is proposed, which has a function with gradient factor, adaptive Nesterov momentum method, and adaptive learning rate for the lightweight analysis of meso parameters. The sensitivity between macro and meso parameters is quantified, and the key meso parameters are screened out. Based on the lightweight model, the correlation and influence mechanisms between macro and meso parameters are analyzed. It was found that the elastic modulus increases linearly with the increase in equivalent modulus. The parallel bond stiffness ratio can inhibit the growth of the elastic modulus, and the elastic modulus decreases greatly when the stiffness is relatively high. There is a linear relationship between Poisson’s ratio and stiffness ratio, and the increase in the friction coefficient will cause the nonlinear decrease in it. The strength parameters have an incentive effect on the peak strength. When the tensile and shear strengths of the parallel bond are at a high level, the combination has the most significant effect on the increase in the peak strength. The internal friction angle mainly has a certain influence on the postpeak strength of the rock, because it has a control effect on the particle sliding on both sides of the shear zone when the sample is loaded after the peak. Based on the central composite experimental design and response surface method, a nonlinear model of macro–meso parameters described by multiple subresponse surfaces is obtained. Finally, the mathematical model of parameter calibration is established, and the optimal solution of rock meso parameters is obtained by using optimization techniques. Through the example verification, it was found that the numerical experiment and laboratory test results are close in the stress characteristics, stress evolution, and failure mode of the sample, which proves the effectiveness and reliability of the calibration method. The research results have a certain reference value for PFC parameter calibration.
In order to explore the influences of fault dislocations on tunnel stability under seismic action, a nonlinear dynamic simulation method for the rock–fault contact system is proposed. First, considering the deterioration effect of seismic action on the ultimate bearing load of the contact interface between rock mass and fault, a mathematical model is established reflecting the seismic deterioration laws of the contact interface. Then, based on the traditional point-to-point contact type in a geometric mesh, a point-to-surface contact type is also considered, and an improved dynamic contact force method is established, which considers the large sliding characteristics of the contact interface. According to the proposed method, a dynamic finite element calculation for the flow of the rock–fault contact system is designed, and the accuracy of the method is verified by taking a sliding elastic block as an example. Finally, a three-dimensional (3D) calculation model for a deep tunnel through a normal fault is built, and the nonlinear seismic damage characteristics of the tunnel under horizontal seismic action are studied. The results indicate that the relative dislocation between the rock mass and the fault is the main factor that results in lining damage and destruction. The seismic calculation results for the tunnel considering the dynamic interaction between the rock mass and the fault can more objectively reflect the seismic response characteristics of practical engineering. In addition, the influences of different fault thicknesses and dip angles on the seismic response of the tunnel are discussed. This work provides effective technical support for seismic fortification in a tunnel through fault.
After the excavation of an underground cavern, how the surrounding rock and the support work together to bear the excavation load is an important prerequisite to correctly analyze the joint force characteristics; effectively play the role of support; and ensure the safety, efficiency, and economy of underground cavern construction. Starting from the elastic-plastic load release characteristics of surrounding rock, this paper proposes a calculation method of the elastic load coefficient of surrounding rock and a graded release method of plastic load, which ensures the actual effect of the synergistic action of the first support and surrounding rock. Based on the elastic-plastic damage evolution characteristics of surrounding rock, a weighted iterative calculation method of elastic-plastic damage is proposed, and an evaluation method of load release ultimate bearing capacity of surrounding rock is determined. By monitoring the change law of rock acoustic wave velocity with surrounding rock damage, the relationship between the wave velocity and the damage coefficient of the surrounding rock in the excavation process is deduced, and it is proposed to determine the latest support time for first support by using the measured rock damage wave velocity. Through the numerical simulation analysis of a diversion tunnel excavation and support, the damage evolution law of the surrounding rock with the release of the excavation load is studied. The ultimate bearing capacity of various surrounding rocks and supporting opportunity is determined. The results demonstrate the validity and practicality of the analysis and calculation methods in this paper, which provide a new idea and analysis method for quantifying the bearing capacity of surrounding rock and determining the support timing in the excavation and support design of underground caverns.