In order to obtain the calibration law of rock macro and meso parameters under three-dimensional conditions, based on the parallel bond model, starting with the basic theory of PFC and the qualitative relationship between macro and meso parameters, an orthogonal experimental scheme is designed. An improved BP algorithm is proposed, which has a function with gradient factor, adaptive Nesterov momentum method, and adaptive learning rate for the lightweight analysis of meso parameters. The sensitivity between macro and meso parameters is quantified, and the key meso parameters are screened out. Based on the lightweight model, the correlation and influence mechanisms between macro and meso parameters are analyzed. It was found that the elastic modulus increases linearly with the increase in equivalent modulus. The parallel bond stiffness ratio can inhibit the growth of the elastic modulus, and the elastic modulus decreases greatly when the stiffness is relatively high. There is a linear relationship between Poisson’s ratio and stiffness ratio, and the increase in the friction coefficient will cause the nonlinear decrease in it. The strength parameters have an incentive effect on the peak strength. When the tensile and shear strengths of the parallel bond are at a high level, the combination has the most significant effect on the increase in the peak strength. The internal friction angle mainly has a certain influence on the postpeak strength of the rock, because it has a control effect on the particle sliding on both sides of the shear zone when the sample is loaded after the peak. Based on the central composite experimental design and response surface method, a nonlinear model of macro–meso parameters described by multiple subresponse surfaces is obtained. Finally, the mathematical model of parameter calibration is established, and the optimal solution of rock meso parameters is obtained by using optimization techniques. Through the example verification, it was found that the numerical experiment and laboratory test results are close in the stress characteristics, stress evolution, and failure mode of the sample, which proves the effectiveness and reliability of the calibration method. The research results have a certain reference value for PFC parameter calibration.
The incident direction of earthquake motion is an important factor affecting the seismic response of underground structures. In this study, a three-dimensional (3D) oblique incidence method of SV waves is proposed and the effects of incident angles of SV waves on the seismic response of a lined arched tunnel are evaluated. Based on wave field decomposition principle and equivalent node force method and together with viscous-spring artificial boundary, the oblique incidence method of SV waves is implemented by transforming seismic wave field into the equivalent nodal forces acting on the artificial boundaries. By deriving the distance of the incident waves and the reflected wave on free surface to artificial boundaries, this method can comprehensively consider the phase difference of the seismic wave propagation and the influence of the damping effect of the rock medium on the seismic wave propagation. The method is programed into a dynamic finite element program and its effectiveness is examined by a numerical example. Consequently, the oblique incidence method is applied to evaluate the seismic behaviors of the tunnel. The numerical results reveal that (1) the oblique incidence of the seismic wave results in a larger seismic response; (2) the response amplitudes of the stress and displacement increase with the increase of incident angles and reaching the maximum in the case of 30° incident angle; (3) the damage extent increases with an increase in the incident angles, and the oblique incidence of the seismic wave is believed to increase the spatial difference of damage distribution.
In order to explore the influences of fault dislocations on tunnel stability under seismic action, a nonlinear dynamic simulation method for the rock–fault contact system is proposed. First, considering the deterioration effect of seismic action on the ultimate bearing load of the contact interface between rock mass and fault, a mathematical model is established reflecting the seismic deterioration laws of the contact interface. Then, based on the traditional point-to-point contact type in a geometric mesh, a point-to-surface contact type is also considered, and an improved dynamic contact force method is established, which considers the large sliding characteristics of the contact interface. According to the proposed method, a dynamic finite element calculation for the flow of the rock–fault contact system is designed, and the accuracy of the method is verified by taking a sliding elastic block as an example. Finally, a three-dimensional (3D) calculation model for a deep tunnel through a normal fault is built, and the nonlinear seismic damage characteristics of the tunnel under horizontal seismic action are studied. The results indicate that the relative dislocation between the rock mass and the fault is the main factor that results in lining damage and destruction. The seismic calculation results for the tunnel considering the dynamic interaction between the rock mass and the fault can more objectively reflect the seismic response characteristics of practical engineering. In addition, the influences of different fault thicknesses and dip angles on the seismic response of the tunnel are discussed. This work provides effective technical support for seismic fortification in a tunnel through fault.
1 January 2017 in Mathematical Problems in Engineering
This study establishes an analytical model for the interaction between the bolt and surrounding rock based on the bearing mechanism of fully grouted rock bolts. The corresponding controlled differential equation for load transfer is deduced. The stress distributions of the anchorage body are obtained by solving the equations. A dynamic algorithm for the bolt considering shear damage on the anchoring interface is proposed based on the dynamic finite element method. The rationality of the algorithm is verified by a pull‐out test and excavation simulation of a rounded tunnel. Then, a case study on the mechanical characteristics of the bolts in underground caverns under seismic loads is conducted. The results indicate that the seismic load may lead to stress originating from the bolts and damage on the anchoring interface. The key positions of the antiseismic support can be determined using the numerical simulation. The calculated results can serve as a reference for the antiseismic optimal design of bolts in underground caverns.
13 January 2020 in Mathematical Problems in Engineering
A numerical analysis method for block failure is proposed that is based on continuum mechanics. First, a mesh model that includes marked blocks was established based on the grid-based block identification method. Then, expressions of the contact force under various contact states were derived based on the explicit contact force algorithm, and a contact simulation method between blocks and the surrounding rock was proposed. The safety factors of the blocks were calculated based on the strength reduction method. This numerical analysis method can simulate both the continuous deformation of the surrounding rock and the discontinuous failure processes of the blocks. A simple example of a sliding block was used to evaluate the accuracy and rationality of the numerical method. Finally, combined with a deep underground excavation project under complex geological conditions, the stability of the blocks and rock were analyzed. The results indicate that the key blocks are damaged after excavation, the potentially dangerous blocks loosen and undergo large deformations, and the cracks between the blocks and the rock gradually increase as the excavation proceeds. The safety factors of the blocks change during the excavation. The numerical results demonstrate the influence of the surrounding rock on the failure process and on the stability of the blocks, and an effective analysis method is provided for the stability analysis of blocks under complex geological conditions.
13 February 2023 in Science China Technological Sciences