Pulse Spray Drying (PSD) has potential as a sustainable means of skimmed milk powder (SMP) production. In this study, powders were obtained from PSD using different drying outlet temperatures (70, 80, 90 and 100 °C), and their characteristics were compared to those of traditional Spray Drying (SD). Native whey proteins were well preserved and Solubility Indexes were over 98% in all cases, despite powders obtained by PSD displaying lower solubility than the SD ones. No visual difference was observable in the powders (ΔE < 2); however, PSD powders were found to be yellower with a higher Browning Index. The drying technology did not have a significant effect on powder moisture content and bulk density. Particle size distribution and scanning electron microscopy images confirmed the presence of fine particles (<10 μm) in all samples that might have provided poor flowability and wetting behavior (overall Carr Index and Hausner ratio were 33.86 ± 3.25% and 1.52 ± 0.07, respectively). Higher amounts of agglomerated particles were found at low temperatures in the products processed with both technologies, but PSD samples showed a narrower particle size distribution and hollow particles with more wrinkles on the surface (probably due to the fast evaporation rate in PSD). Overall, PSD provided SMP with comparable physicochemical characteristics to SD and, once optimized at the industrial level, could offer significant advantages in terms of thermal efficiency without significant modification of the final product quality.
Electric fields have been used in the manufacturing of powders in a number of ways, including to enhance drying rates and retain heat-sensitive materials. Electrohydrodynamic drying and electrostatic spray drying use electric fields to accelerate the evaporation of liquid from a surface, resulting in faster drying times and improved product quality. These technologies are used in the food and pharmaceutical industries to manufacture powders from liquid feed materials. In addition to enhancing drying rates, the use of electric fields in powder manufacturing can also help to retain the bioactivity of compounds in the final product. Many bioactive compounds are sensitive to heat and can be degraded or destroyed during conventional drying processes. By using electric fields to dry powders, it is possible to reduce the amount of heat applied and therefore preserve the bioactive compounds in the final product. This article reviews the different mechanisms of various electric field assisted technologies, i.e., electrohydrodynamic atomization, electrohydrodynamic drying, pulsed electric fields and a new approach of electrostatic spray drying, along with their potential food industry applications.
19 February 2021 in Food and Bioprocess Technology
The goal of this study was to investigate the changes in oil droplet size in whey protein–stabilized emulsions during the atomization and the subsequent drying step of a spray drying process. For this purpose, experiments were performed in an atomization rig and a pilot spray dryer with two commercial pressure swirl atomizers. By comparing the oil droplet size before atomization, after atomization, and after spray drying, the changes in oil droplet size during each process step were quantified. The effect of oil droplet breakup during atomization was isolated by atomizing emulsions with 1 wt.% oil content and a protein to oil concentration ratio of 0.1. At 100 bar, the Sauter mean diameter of oil droplet size was reduced from 3.13 to 0.61 μm. Directly after breakup, coalescence of the oil droplets was observed for emulsions with a high oil content of 30 wt.%, leading to a droplet size after atomization of 1.15 μm. Increasing the protein to oil concentration ratio to 0.2 reduced coalescence during atomization and oil droplets with a mean diameter of 0.92 μm were obtained. Further coalescence was observed during the drying step: for an oil content of 30 wt.% and a protein to oil concentration ratio of 0.1 the mean droplet size increased to 1.77 μm. Powders produced at high oil contents showed a strong tendency to clump. Comparable effects were observed for a spray drying process with a different nozzle at 250 bar. The results confirm that droplet breakup and coalescence during atomization and coalescence during drying have to be taken into consideration when targeting specific oil droplet sizes in the product. This is relevant for product design in spray drying applications, in which the oil droplet size in the powder or after its redispersion determines product quality and stability.
Electrostatic spray drying (ESD) of a milk protein matrix comprising whey protein isolate (WPI), skim milk powder (SMP), and lactose was compared to conventional spray drying (CSD) and freeze-drying (FD). ESD and CSD were used to produce powders at low (0.12–0.14), medium (0.16–0.17), and high (0.31–0.36) levels of water activity (aw), while FD powders targeted low aw (0.12). Maillard reaction indicators were studied after drying and during storage for up to 28 days at 20, 40, or 60 °C by measuring free -NH2 groups, as an indicator of available lysine, and 5-hydroxymethylfurfural (HMF). After drying, levels of residual free -NH2 groups were ~15% higher in ESD and FD powders than in their CSD counterparts. CSD powders also had ~14% higher HMF concentrations compared to their ESD and FD counterparts. Storage led to reductions in free -NH2 groups and increases in HMF content in all powders, the extent of which increased with increasing storage temperature. Reductions in free -NH2 groups followed first-order reaction kinetics at 20 and 40 °C but second-order reaction kinetics at 60 °C. Lactose crystallization was detected in high-aw CSD powders after 14 d at 40 °C and in both CSD and ESD powders after 7 d at 60 °C. Overall, we found that ESD is a gentle drying technology which enables production of powders with lower Maillard reaction markers.