We present a compact, versatile Hall readout system with digital output, fully integrated in 180nm technology. The core of the system is an instrumentation amplifier architecture that provides inherent anti-aliasing filtering, where the anti-aliasing characteristic is locked into a shape that maximally prevents aliasing to low frequencies. The efficiency for blocking out-of-band white noise is comparable to that of a second-order filter, eliminating the need for an explicit anti-aliasing filter before the ADC. Chopping/spinning is applied for up-modulating offset and 1/f noise to just beyond the signal band. A mostly-digital ripple reduction loop (RRL) is added for mitigating offset-related dynamic range limitations. In this, a bilinear integrator is introduced for eliminating the impact of the RRL on the system's DC gain. Moreover, the resolution of the DAC generating the analog offset compensation is reduced significantly, and the effect thereof is eliminated by digital noise cancellation logic. The one-step amplification and the simple, low-resolution DAC for offset compensation both aid in keeping the area footprint low: the analog circuits (including DAC and ADC) only occupy 0.21mm 2 . Notable performance characteristics are an input-referred noise floor of 55nT/ √{Hz} within a 410kHz bandwidth, a current consumption of only 5.1mA, and a 47dB dynamic range. The amplifier architecture can be easily applied as an analog preconditioning circuit in other sensor readout situations as well.
12 April 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents an asynchronous double-edge triggered Gray counter that can advantageously be used as coarse counter in a coarse-fine VCO ADC. We show that, in spite of using only a single counter and a single sampling register, it is possible to resolve the ambiguity in the coarse counter value caused by metastability and delay. We present simple decoding logic that performs both Gray-to-binary conversion and ambiguity resolution. A comparative case study is made for an 11 bit coarse-fine architecture based on the new Gray counter and a prior-art double-sampling binary counter. A reduction of 21% in area has been obtained, while at the same time post-layout simulations show a power saving of 17.5%.
26 February 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief identifies the cause of frequency-dependent distortion in ring oscillator voltage-controlled oscillator (VCO) analog-to-digital converters (ADCs). First, a VCO model is presented which takes into account the capacitance at the VCO terminals. This allows the most common drive configurations to be analyzed to determine the origin of the frequency-dependent distortion and the vulnerability of the different drive configurations. A conclusion is that voltage control is relatively robust against this effect. Based on the preceding analysis, a novel foreground calibration procedure is developed. The effectiveness of the proposed calibration method is demonstrated for a manufactured open-loop VCO ADC in 28nm CMOS and compared to results obtained using a prior art calibration method and results without calibration. For a 750 mVpp 26.5 MHz signal, the proposed calibration procedure leads to an improvement in THD of 20 dB and 47 dB compared to results using prior art calibration and no calibration respectively.
24 November 2016 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a power reduction technique for continuous time sigma-delta modulators (CTSDMs). The approach consists of two elements. First, a passive low-pass filter is added in front of the modulator's loop filter to reduce the high frequency components in the loop. As a result, the slew rate requirements of the opamps can be greatly reduced which allows a significant power saving. Unfortunately, the insertion of this low-pass filter also changes the modulator's loop gain, and hence affects the noise transfer functions (NTFs) and signal transfer functions (STFs), in an undesired way. Therefore, the second proposed element consists of inserting a compensation branch which is such that the original loop gain, NTF and STF are restored. Thanks to this, our power saving technique is completely transparent on the system level such that all established techniques and toolboxes for CTSDM design can still be used. The technique is especially suited for one-bit CTSDMs, where the amount of high-frequency components in the loop is excessive. To showcase the technique, a self-oscillating sigma-delta modulator (which is a dedicated type of one-bit CTSDM) was implemented in a 65-nm CMOS process. It achieves a peak signal to noise and distortion ratio of 63 dB over a 20-MHz bandwidth at a power consumption of 1.7 mW while occupying a very small chip area of only 0.009 mm 2 .
In this paper, a Hall plate readout with a randomized four-phase spinning-current scheme is proposed. The goal is to remove the maximum number of offset components, including the offset associated with spike demodulation. The outcome is that only the smallest possible offset remains, corresponding to the residual offset of the Hall plate which cannot be distinguished from the Hall signal. An additional innovation is to operate various offset-reduction loops in spread-spectrum mode, allowing the removal of error components without notching out any in-band signals. The resulting approach delivers a very large notch-free bandwidth while simultaneously reducing the Hall plate residual offset, making it an enabler for high-bandwidth Hall-based current sensors. To demonstrate the proposed techniques, we have realized a mixed-mode experimental circuit, where the analog part is implemented in a custom integrated circuit, and the digital control system in an FPGA is connected to the analog chip. Measurement results feature a Hall readout system with a notch-free bandwidth up to 820 kHz and a 47 Trms noise floor. The input-referred Hall plate offset, based on statistical measurements on 10 samples from a single wafer, is reduced from to only .
4 September 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
In this work, a 3.5 GS/s voltage-controlled oscillator (VCO) analog-to-digital converter (ADC) using multi-stage noise shaping (MASH) is presented. This 28nm CMOS ADC achieves second-order noise shaping in an easily-scalable, open-loop configuration. A key enabler of the high-bandwidth MASH VCO ADC is the use of a multi-bit estimated error signal. With an OSR of 16, an SNDR of 67 dB and DR of 68 dB are achieved in 109.375 MHz bandwidth. The full-custom pseudo-analog circuits consume 9 mW, while the automatically generated digital circuits consume another 24 mW. A $\mathbf{FoM_{DR} = 163}$ dB and core area of $\mathbf{0.017\,\mathbf{mm}^2}$ are obtained.