The rapid advancement of engineering systems has spurred the search for innovative thermal management solutions. Boiling, as a phase‐change heat transfer method, has shown promise in heat dissipation, but non‐functionalized surfaces struggle with increasing cooling demands. To improve heat dissipation efficiency across different heat loads, functionalized surfaces with tailored wettability have been proposed. Separately, superhydrophilic and superhydrophobic surfaces each offer benefits and drawbacks in boiling applications but combining them on a single “biphilic” surface simultaneously harnesses their advantages. In this study, laser‐functionalized copper surfaces with spatially tailored wettability are developed by combining two‐step laser texturing with a self‐assembled monolayer coating, while focus is placed on the impact of the size and pitch of superhydrophobic spots. The developed functionalized surfaces exhibit exceptional boiling performance with heat transfer coefficients up to 299 kW m⁻² K⁻¹, a 434% enhancement over untreated surfaces. Optimal ratios of superhydrophilic and superhydrophobic areas and optimal spot pitch are identified. Additionally, varying behavior at different heat flux levels is observed, emphasizing the importance of considering thermal loads when determining the optimal surface pattern. This advancement in performance, along with the rapid and cost‐effective functionalization process, represents a significant breakthrough for enhanced thermal management applications.

The enhancement of boiling heat transfer has been extensively shown to be achievable through surface texturing or fluid property modification, yet few studies have investigated the possibility of coupling both enhancement approaches. The present work focuses on exploring the possibility of concomitant enhancement of pool boiling heat transfer by using TiO₂-water nanofluid in combination with laser-textured copper surfaces. Two mass concentrations of 0.001 wt.% and 0.1 wt.% are used, along with two nanoparticle sizes of 4–8 nm and 490 nm. Nanofluids are prepared using sonification and degassed distilled water, while the boiling experiments are performed at atmospheric pressure. The results demonstrate that the heat transfer coefficient (HTC) using nanofluids is deteriorated compared to using pure water on the reference and laser-textured surface. However, the critical heat flux (CHF) is significantly improved at 0.1 wt.% nanoparticle concentration. The buildup of a highly wettable TiO₂ layer on the surface is identified as the main reason for the observed performance. Multiple subsequent boiling experiments using nanofluids on the same surface exhibited a notable shift in boiling curves and their instability at higher concentrations, which is attributable to growth of the nanoparticle layer on the surface. Overall, the combination of nanofluids boiling on a laser-textured surface proved to enhance the CHF after prolonged exposure to highly concentrated nanofluid, while the HTC was universally and significantly decreased in all cases.

Prior studies have evidenced the potential for enhancing boiling heat transfer through modifications of surface or fluid properties. The deployment of nanofluids in pool boiling systems is challenging due to the deposition of nanoparticles on structured surfaces, which may result in performance deterioration. This study addresses the use of TiO₂–water nanofluids (mass concentrations of 0.001 wt.% and 0.1 wt.%) in pool boiling heat transfer and concurrent mitigation of nanoparticle deposition on superhydrophobic laser-textured copper surfaces. Samples, modified through nanosecond laser texturing, were subjected to boiling in an as-prepared superhydrophilic (SHPI) state and in a superhydrophobic state (SHPO) following hydrophobization with a self-assembled monolayer of fluorinated silane. The boiling performance assessment involved five consecutive boiling curve runs under saturated conditions at atmospheric pressure. Results on superhydrophilic surfaces reveal that the use of nanofluids always led to a deterioration of the heat transfer coefficient (up to 90%) compared to pure water due to high nanoparticle deposition. The latter was largely mitigated on superhydrophobic surfaces, yet their performance was still inferior to that of the same surface in water. On the other hand, CHF values of 1209 kW m⁻² and 1462 kW m⁻² were recorded at 0.1 wt.% concentration on both superhydrophobic and superhydrophilic surfaces, respectively, representing a slight enhancement of 16% and 27% compared to the results obtained on their counterparts investigated in water.