Infrared measurements are used to assess the measurement accuracy of the peak gate current (IGPeak) method for Insulated-gate bipolar transistor (IGBT)junction temperature measurement. Single IGBT chips with the gate pad in both the center and the edge are investigated, along with paralleled chips, as well as chips suffering partial bondwire lift-off. Results are also compared with a traditional electrical temperature measurement method: the voltage drop under low current (VCE (low )). In all cases, the IGPeak method is found to provide a temperature slightly overestimating the temperature of the gate pad. Consequently, both the gate pad position and chip temperature distribution influence whether the measurement is representative of the mean junction temperature. These results remain consistent after chips are degraded through bondwire lift-off. In a paralleled IGBT configuration with nonnegligible temperature disequilibrium between chips, the IGPeak method delivers a measurement based on the average temperature of the gate pads.
4 June 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes a separated test method for studying the current effect on the ageing process of wire-bonded Silicon Carbide (SiC) MOSFET module under power cycling test (PCT). The separated test method enables to test SiC MOSFET with different load current densities, but under the same temperature swing and average temperature conditions. By analyzing the output characteristics in the linear region, the relations among the gate voltage, on-state voltage and junction temperature are revealed. Then, the one-to-one correspondence between gate voltage and conduction power loss can be used to adjust the current density with the same temperature conditions. Two six-pack SiC modules (1200V/20A) are tested under 12A and 24A conditions to experimentally verify the proposed method. The ageing curves show that the higher current can speed up the ageing rate of bond wires even under the same temperature conditions (65°C ~ 125°C). Moreover, the high current density also has an impact on the solder layer degradation as well as the temperature conditions. Finally, power device analyzer B1506A and Scanning Acoustic Microscopy (SAM) are used to investigate the degradation of electrical parameter and solder layer, respectively. The final summary of analytical results shows that the input current has a non-negligible impact on the degradation process of power module.
16 July 2018 in IEEE Transactions on Industrial Electronics
This letter experimentally demonstrates the temperature dependence of the Flatband Voltage (VFB) in high power Insulated-Gate-Bipolar-Transistors (IGBTs). The gate voltage during the turn-on delay is shown to fluctuate up to 5mV/°C as a result of this temperature dependence. We investigate the practical use of this temperature dependence as an addition to the genre of IGBT junction temperature measurement methods known as Temperature Sensitive Electrical Parameters (TSEPs). The letter will outline some possible measurement circuits and highlights issues with the VFB that may make its use as a TSEP problematic.
In fast switching power semiconductors, the use of a fourth terminal to provide the reference potential for the gate signal—known as a kelvin-source terminal—is becoming common. The introduction of this terminal presents opportunities for condition monitoring systems. This article demonstrates how the voltage between the kelvin-source and power-source can be used to specifically monitor bond-wire degradation. Meanwhile, the drain to kelvin-source voltage can be monitored to track defects in the semiconductor die or gate driver. Through an accelerated aging test on 20 A Silicon Carbide Metal-Oxide-Semiconductor-Field-Effect Transistors (MOSFETs), it is shown that there are opposing trends in the evolution of the on-state resistances of both the bond-wires and the MOSFET die. In summary, after 50,000 temperature cycles, the resistance of the bond-wires increased by up to 2 mΩ, while the on-state resistance of the MOSFET dies decreased by approximately 1 mΩ. The conventional failure precursor (monitoring a single forward voltage) cannot distinguish between semiconductor die or bond-wire degradation. Therefore, the ability to monitor both these parameters due to the presence of an auxiliary-source terminal can provide more detailed information regarding the aging process of a device.
Silicon Carbide MOSFETs are now widely available and have frequently been demonstrated to offer numerous advantages over Silicon based devices. However, reliability issues remain a significant concern in their realisation in commercial power electronic systems. In this paper, a test bench is designed that enables an accelerated power cycling test to be performed on packaged Silicon Carbide MOSFETs (TO-247) under realistic operating conditions. An accelerated power cycling test is then performed, with on-state resistance selected as the observed parameter to detect degradation. On-state resistance is routinely monitored online through the use of an innovative voltage measurement system. The packaged Silicon Carbide MOSFET is shown to exhibit a 25% increase in on-state resistance as the device ages throughout its lifetime, with the test still on-going.