The purpose of this work is to investigate the effect of the WC content on the surface characteristics and nanoindentation behaviors of WC/Ni-based composite laser-clad coatings. Four NiCrSiBC coatings with WC wt% of 30%, 40%, 50%, and 60%, respectively, were clad on carbon steel substrates using a laser. The morphologies and phase compositions of four clad coatings were comparatively observed. In addition, the hardness and elastic modulus values of the four coatings were measured and quantitatively calculated. As a result, with the increase in WC, the coating grains were more refined. Meanwhile, cracks and WC particle breakage occurred in the 50–60% WC coatings, whereas this was not found in the 30–40% WC coatings. When the WC content increased from 40% up to 50%, the coating hardness and elastic modulus significantly increased. However, a further increase in WC from 50% to 60% did not result in considerable improvement in coating quality but considerably worsened the coating’s cracking behavior instead. Therefore, for WC/Ni-based composite coatings, a threshold exists for the WC content, and this value was 50% within the experimental scope of this study.

A set of ultrasonic burnishing equipment with two different burnishing tips was designed and manufactured, with which a series of experiments were performed to explore the effects of process parameters and burnishing tips on the surface integrity of austenitic stainless steel material being treated by ultrasonic burnishing (UB). Based on the experiment data, the two surface treatments, i.e. UB with ball tip and UB with roller tip, were comparatively assessed together with the other two surface machining methods of fine turning and grinding. As a further study, a microscopic FE model was built to investigate the three-dimensional transient stress and strain field inside the being treated material. It was found that parameter combination is determinative to surface finishing in UB process, and static pressure and burnishing pass are supposed to be the two most significant parameters for surface integrity of the treated sample. On the whole, roller tip is more preferable to achieve good surface enhancement than ball tip. The superposition of ultrasonic vibration leads to the dynamic change of the stress and strain field in UB, resulting in the oscillating propagation of stress wave inside the material, which gives explanation for the good performance of UB than that of conventional burnishing without ultrasonic.

The preparation of functional coatings on metal substrates is an effective method to enhance the surface of steel structures with good serviceability in applications for engineering parts. The objective of this research is to analyze the surface properties of two sorts of medium-entropy alloy (MEA) coatings prepared by laser cladding. After cladding, the two prepared coatings were strengthened by ultrasonic burnishing (UB) treatment. Cladding coating samples before and after being UB-treated were comparatively tested in order to investigate the process effects of UB. When compared with corresponding untreated coating samples, the roughness values of the two sorts of UB-treated samples were decreased by 88.7% and 87.6%, the porosities were decreased by 63.8% and 73.4%, and the micro-hardness values were increased by 41.7% and 32.7%, respectively. Furthermore, the two sorts of UB-treated coating samples exhibited better mechanical properties and wear resistance than corresponding untreated samples.

The contact stress and heating effect between the cutting tool and workpiece in metal machining is symmetrical. However, the symmetry may be destroyed by changes in the workpiece material mechanical properties, such as ductility. The goal of this study is to reveal the wear characteristics of the cutting tool in machining a ductile metal with the cutting speed at which the metal is embrittled by the high-strain-rate-embrittle effect (HSREE). Orthogonal high-speed turning experiments were carried out. Pure iron type DT8 was cut at different cutting speeds, ranging from 1000 m/min to 9000 m/min. The shape and morphology of the chips obtained in the experiment were observed and analyzed by optical microscope and scanning electron microscope (SEM). Tool wear characteristics at different cutting speeds were observed. It shows that the pure iron becomes completely brittle when the cutting speed is higher than 8000 m/min. On the rake face, the coating of the cutting tool bursts apart and peels off. A matrix crack originates in the cutting edge or rake face and extends to the flank face of the cutting tool. The effects of HSREE on the tool wear is discussed. The findings of this study are helpful for choosing a suitable tool for brittle cutting of the ductile metal pure iron with very high cutting speed and solving the problems in machining due to its high ductility and high stickiness.