This study presents a detailed computational investigation of internal flow dynamics within a centrifugal compressor using advanced computational fluid dynamics techniques. The primary objective is to elucidate the thermodynamic interactions and flow structures influencing compressor performance across various operating conditions. High-fidelity simulations are performed on a single-passage configuration at a fixed rotational speed of 80 000 rpm, capturing critical phenomena such as flow separation, vortex leakage, recirculation zones, and secondary flows. A comprehensive hub-to-shroud analysis reveals the spatial evolution of pressure fields, temperature gradients, and turbulence characteristics, highlighting distinct aerodynamic regimes: uniform flow with minimal gradients near the hub (20% span), balanced effects at mid-span (50%), and intensified flow disturbances and thermal gradients near the shroud (80%). The results emphasize the dominance of secondary flows and separation, particularly under off-design conditions, with complex helical structures and recirculation zones becoming more prominent at higher pressure ratios. Blade loading analysis further indicates that the leading-edge and tip regions are most susceptible to adverse pressure gradients and flow detachment. These findings underscore the critical importance of geometric optimization in mitigating loss-inducing flow features and improving compressor efficiency. The outcomes offer valuable insights for enhancing the performance and reliability of compressors in diesel engine applications and contribute to the broader field of high-performance turbomachinery design.
20 December 2023 in Progress in Agricultural Engineering Sciences
In order to improve the thermal performance of heat exchangers and air collectors, we insert various forms of artificial roughness, known as ribs, into the useful duct. These ribs promote the creation of turbulent flows and enhance heat transfer by conduction, convection and radiation. However, the introduction of these ribs leads to an increase in pressure drop, requiring higher mechanical power to pump the heat transfer fluid. This experimental study focuses on estimating, using empirical approaches, the pressure losses induced by rectangular ribs with an inclined top. The ribs are made from 0.4 mm galvanized sheet steel. An experimental set-up was designed to measure the head losses generated by the ribs, from the point of entry to the point of exit from the useful duct. Using the dimensional analysis method, correlations were established to evaluate head losses as a function of flow regime and rib geometry and configuration (including different geometries for rib arrangement over the configuration area). In order to improve the thermal performance of heat exchangers and air collectors, we insert various forms of artificial roughness, known as ribs, into the useful duct. These ribs promote the creation of turbulent flows and enhance heat transfer by conduction, convection and radiation. However, the introduction of these ribs leads to an increase in pressure drop, requiring higher mechanical power to pump the heat transfer fluid. This experimental study focuses on estimating, using empirical approaches, the pressure losses induced by rectangular ribs with an inclined top. The ribs are made from 0.4 mm galvanized sheet steel. An experimental set-up was designed to measure the head losses generated by the ribs, from the point of entry to the point of exit from the useful duct. Using the dimensional analysis method, correlations were established to evaluate head losses as a function of flow regime and rib geometry and configuration (including different geometries for rib arrangement over the configuration area).
The main objective of this work is to determine the graphs of relative humidity loss, and the speed of drying for green pepper, to identify the characteristic parameters influencing the drying of products with high humidity content, and to establish satisfactory models that characterize the drying kinetics. This experimental study was carried out using an indirect type of a solar dryer, which functions in the mode of natural convection, intended for the thermal treatment to medium duration of the agro-alimentary products. In this work, we are interested in the evolution of the temperature and the mass of the material to be dried, whose manipulations took place in May and July of the year 2009.
The equilibrium water content of a product to be dried is essential during storage and solar drying operation by forced convection. These values are often taken from the so-called sorption isotherm graphs. The determination of these isotherms is an essential step to knowing the distribution and the intensity of the water bonds in the products in use. They allow determining the final water content to be reached to optimize the drying conditions of these products and give valuable information on the hygroscopic equilibrium. Therefore, the present work proposes to determine experimentally the desorption isotherms of a medicinal and aromatic agricultural product (mint), using the saturated saline solution method. The experiment is carried out for four different values of temperature: 20°C, 35°C, 45°C and 55°C to study the influence of temperature on the equilibrium graphs of the product and to describe the desorption isotherm of mint for each temperature using a polynomial regression of the experimental points found. Finally it was compared with the Henderson model.