Bluetooth Low Energy (BLE) has been significantly contributed to Internet of Things applications due to its advantages, such as low power consumption and scalability. To further expand its applications, BLE has adopted the angle of arrival (AoA) and the angle of departure (AoD) to improve the accuracy in direction finding (DF). The AoA/AoD is calculated using the phase difference (PD) between slots in the received BLE data. The PD performance of BLE receiver (RX) in all directions should be evaluated in detail because it directly determines the accuracy of AoA/AoD. In the traditional test method, the reference PD is converted by an antenna array with switches, which is inaccurate due to the conversion errors and path mismatches. Moreover, because of the mechanical rotation of the turntable, the test processing is very time-consuming. This paper propose a BLE test waveform generation method that directly includes the reference PD. A commonly-used vector signal generator (VSG) is the only required instrument in the evaluation. The compact test setup not only eliminates the requirement of antenna array, switch, turntable, and anechoic chamber, but also eliminates the measurement errors caused by these devices. After creating and downloading all BLE test waveforms with reference PD in the range of -180∘ to 180∘ by user-defined steps, the PD performance of BLE RX can be quickly evaluated by switching the test waveforms using commands or running them in the sequence mode. Furthermore, three enhanced test cases with automatic test procedures are proposed to evaluate the detailed PD accuracy of BLE RX under the low signal to noise ratio (SNR), carrier frequency offset and modulation frequency deviation environments. Experimental results show that the PD error of proposed method is 0.19∘, and it needs 360ms to evaluate the PD accuracy of CC2640R2F in all directions in 1∘ steps.
26 July 2023 in IEEE Transactions on Nanotechnology
An accuracy-configurable adder (ACA) meets various requirements in energy efficiency and accuracy of many applications. However, it suffers from problems such as a large hardware cost for performing configurations. In this article, we propose two energy-efficient transistor-level accuracy-configurable full adders, referred to as a positive ACA (PACA) and a negative ACA (NACA). Each design uses only two transistors as switches driven by an enable signal to configure the accurate and approximate modes. Dynamic accuracy-configurable adders (DACAs) are further developed by cascading the PACAs or NACAs. The DACA design realizes a remarkable trade-off between accuracy and performance by switching between different degrees of approximations. Simulation results show that compared with an accurate adder, a 16-bit DACA provides a saving of up to 43.61% in power and a reduction of 83.31% in delay, with only a loss of 11.96% in accuracy. The advantage of the DACA is illustrated by applications of image processing and classification using a neural network model.
9 December 2019 in IEEE Internet of Things Journal
Bluetooth low-energy (BLE) beacons have been used in a variety of IoT applications. This article proposes a compact and cost-effective BLE beacon, which only uses a 2.4-GHz Gaussian frequency-shift keying (GFSK) transceiver and an ultralow power 8-bit 16-MHz microcontroller unit (MCU). The minimum requirements and the data processing procedure for commonly used GFSK transceivers to generate the BLE-compatible advertising packages are also provided in this article. Benefited from the compact architecture and the simple generation procedure, the BLE-compatible packages can be directly controlled to broadcast at any given radio frequency (RF) channel or time. Based on the flexible characteristics of our proposed beacon, the multiprotocol and dynamic content advertising are developed in this article. With the help of multiprotocol and dynamic content advertising, the proposed beacons can be used to provide more sophisticated services. Since the broadcast channels and time are freely controlled, the proposed BLE beacons are also very suitable for anti-collision applications with custom-defined channels and time intervals. The experimental results show that the proposed beacon can broadcast BLE-compatible protocol data units (PDUs) at a minimum interval of about 1 ms. The measured average current is about 51 uA when the advertising interval is 800 ms. Different protocols and dynamic content PDUs generated by the proposed beacon can be properly received by BLE-enabled devices, proving that they are fully compatible with the BLE specification. The measured bit rate of the proposed beacon in dynamic content advertising is about 198.4 kb/s.
Near-threshold voltage (NTV) operation has the potential to improve the energy efficiency of digital integrated circuits. However, the use of a conservative timing guard band to avoid the timing errors introduces excessive timing margins, thus causing larger energy dissipation in the NTV region. An error-tolerant design based on timing error detection and correction circuits has been shown to be a promising solution to mitigate these issues. This paper presents a light-weight timing error-tolerant flip-flop (ETFF) design. This design detects timing errors using a node transition signal detector with only nine transistors and corrects these errors during the same clock cycle. Moreover, transistor sizing is explored to optimize the trade-off between performance and area overhead. The proposed ETFFs are inserted into a monitored circuit by replacing original flip-flops at timing-monitored points. To further reduce the overhead, we develop a mean-time-to-failure-aware method to select the monitored points by simultaneously considering the critical path coverage and activation rates of flip-flops. The simulation results show that a CNN accelerator using the proposed timing error-tolerant design implemented in the SMIC CMOS 40 nm process can robustly work at 1.1–0.3 V with only 3.5% area overhead. Furthermore, this design reduces the area overhead by 54.68% and improves the energy efficiency by 53.69% at 0.6 V, compared with the Razor flip-flop design. The advantage of the proposed design lies in that it requires smaller circuit overheads and can work reliably in a wider range of supply voltages.
8 March 2017 in Peer-to-Peer Networking and Applications
Arrhythmia poses a significant threat to human health. Accurate and real-time arrhythmia detection using electrocardiogram (ECG) signals is critical for medical diagnosis. With the rapid development of deep learning technologies, Deep Neural Networks (DNNs) have considerably improved the accuracy of arrhythmia monitoring. However, deploying these techniques on power-constrained wearable devices for real-time monitoring remains challenging. Lightweight designs have thus become essential for achieving low-power and high-throughput real-time detection with limited hardware resources. Binary Neural Networks (BNNs), as a promising lightweight method, exhibit significant potential in reducing hardware resource usage and enhancing inference speed. Nevertheless, existing binarized ECG detection accelerator designs have not yet conducted architectural Design Space Exploration (DSE), and therefore do not sufficiently balance the trade-off between throughput and power consumption. To address this, we propose a highly energy-efficient one-dimensional BNN accelerator for ECG detection. First, we develop a hardware-friendly BNN algorithm by eliminating fully connected layers and nonlinear computations. Subsequently, for the first time, this work utilizes Timeloop to analyze the optimal mapping of the BNN algorithm onto hardware, identifies the optimal accelerator dataflow, and conducts in-depth optimization of both the dataflow and the accelerator hardware circuits based on the Field-Programmable Gate Array (FPGA) architecture. Finally, we introduce a prediction mechanism for fine-grained power control by dynamically disabling redundant computational logic. Experimental results demonstrate that the proposed accelerator achieves a latency of 105.79 $\mu $ s, power consumption of 160 mW, throughput of 112.2 GOPS, and energy efficiency of 701.51 GOPS/W at 100 MHz. Compared with state-of-the-art Xilinx FPGA-based ECG detection accelerators, our design improves energy efficiency by $15.56\sim 3220.89$ times.