Basalt fiber (BF) has a high mechanical strength, excellent temperature resistance, good chemical stability, low energy consumption, and an environmentally friendly production process. In addition, BF-reinforced polymers (BFRPs) have good corrosion resistance and designability; thus, they meet the application requirements of electrical equipment, such as new conductors, insulating pull rods, and composite cross-arms. However, there are still a series of technical issues in the mass production of BF, and the stability of the products needs to be further improved. Therefore, the research on the production, modification, and application of BF is necessary. This paper discusses the chemical composition and production technology of BF, describes the morphology and properties of BF, summarizes the interface problems and modification methods of composites, and finally, introduces the application prospects of BF in the field of electrical materials, which is expected to provide a reference for the application and promotion of BFRP in the future.

Basalt fiber (BF) has high mechanical strength, good insulation performance and low cost. It is suitable to be used as reinforcement material in the manufacture of electrical equipment. However, the large surface inertia of basalt fiber makes it difficult to combine with the matrix material, which seriously limits its service life and application scenarios. In addition, the serious vacancy in the research of insulation properties also limits its production and application in the electrical field. Therefore, in order to solve the problem of difficult bonding between basalt fiber and resin matrix and make up for the research blank of basalt fiber composites in insulation performance, this paper provides a basalt fiber modification method—SiO₂ coating, and tests the insulation and mechanical properties of the modified composite. We used nano-SiO₂ coating solution to modify basalt fiber, and manufactured BF/resin composite (BFRP) by hand lay-up and hot-pressing technology, and experimentally analyzed the influence of nano-SiO₂ content on the mechanical and insulation properties of the modified composite. Fourier transform infrared spectrum and scanning electron microscope analysis showed that nano-SiO₂ was successfully coated on basalt fibers. Through the microdroplet debonding test, it was found that the IFSS of fiber/resin was improved by 35.15%, 72.97 and 18.9%, respectively, after the modification of the coating solution with SiO₂ concentration of 0.5%, 1% and 1.5%, showing better interface properties; the single fiber tensile test found that the tensile strength of the modified fiber increased slightly. Among all composites, 1 wt% SiO₂ coating modified composites showed the best comprehensive properties. The surface flashover voltage and breakdown field strength reached 13.12 kV and 33 kV/mm, respectively, which were 34.6% and 83% higher than unmodified composite. The dielectric loss is reduced to 1.43%, which is 33.8% lower than the dielectric loss (2.16%) of the untreated composite, showing better insulation ability; the tensile strength, bending strength and interlaminar shear strength were increased to 618.22 MPa, 834.74 MPa and 16.29 MPa, respectively, which were increased by 53%, 42.4% and 59.7%, compared with untreated composites. DMA and glass transition temperature showed that the modified composite had better heat resistance. TGA experiments showed that the resin content of the modified composite increased, and the internal structure of the composite became denser.

This paper presents a study that conducted 5000 h of multi-factor aging tests on 10 kV composite crossarms, considering the natural environment in coastal areas and actual power line operations. Various aging conditions, such as voltage, rain, temperature, humidity, salt fog, ultraviolet light, and mechanical stress, were applied during the tests. The research initially analyzed the influence of multi-factor aging on the bending and tensile properties of the full-size composite crossarm. Subsequently, a detailed investigation was carried out to assess the impact of aging on the mechanical properties, electrical insulation properties, and microscopic characteristics of the composite crossarm core bar. Results indicated that the tensile strength and bending strength of the full-size composite crossarm mandrel experienced minimal changes after aging, remaining well within operational requirements. However, the silicone rubber outer sheath’s hydrophobicity decreased, leading to the appearance of cracks and holes on the surface, which provided pathways for moisture and salt infiltration into the mandrel. As a consequence, the bending strength and shear strength of the mandrel material were reduced by 16.5% and 37.7%, respectively. Moreover, the electrical performance test demonstrated a slight change in the mandrel’s leakage current, while the electrical breakdown strength decreased by 22.8%. Microscopic analysis using SEM, three-dimensional CT, and TGA revealed that a small amount of resin matrix decomposed and microcracks appeared on the surface. Additionally, the fiber-matrix interface experienced debonding and cracking, leading to an increased moisture absorption rate of the mandrel material.

Hydrogen is a clean energy carrier with broad application potential. This study focuses on improving hydrogen production efficiency in a proton exchange membrane (PEM) electrolyzer system that integrates a photovoltaic (PV) array, a battery energy storage system, and the electrolyzer. The PV array is interfaced with the electrolyzer through a buck converter using a maximum power point tracking (MPPT) algorithm to ensure maximum energy harvesting. A key contribution of this work is the integration of a battery system through a dual-active-bridge (DAB) converter. The DAB converter employs a multilayer perceptron (MLP) model to dynamically regulate the electrolyzer current and maintain optimal operating efficiency. An adaptive energy management strategy is further proposed to address solar irradiance fluctuations and enhance long-term operational stability. The MLP model is developed in Python and embedded into a PLECS simulation environment. The simulation results verify the effectiveness of the proposed control approach and efficiency optimization scheme. Throughout the simulation period, the PEM electrolyzer sustains an optimal efficiency of 69.9% under maximum PV power output. A limitation of this study is that the efficiency model is derived from the literature and does not yet consider all operational factors, indicating the need for refinement in future work.