Basalt fiber (BF) has a high mechanical strength, excellent temperature resistance, good chemical stability, low energy consumption, and an environmentally friendly production process. In addition, BF-reinforced polymers (BFRPs) have good corrosion resistance and designability; thus, they meet the application requirements of electrical equipment, such as new conductors, insulating pull rods, and composite cross-arms. However, there are still a series of technical issues in the mass production of BF, and the stability of the products needs to be further improved. Therefore, the research on the production, modification, and application of BF is necessary. This paper discusses the chemical composition and production technology of BF, describes the morphology and properties of BF, summarizes the interface problems and modification methods of composites, and finally, introduces the application prospects of BF in the field of electrical materials, which is expected to provide a reference for the application and promotion of BFRP in the future.

Basalt fiber (BF) has high mechanical strength, good insulation performance and low cost. It is suitable to be used as reinforcement material in the manufacture of electrical equipment. However, the large surface inertia of basalt fiber makes it difficult to combine with the matrix material, which seriously limits its service life and application scenarios. In addition, the serious vacancy in the research of insulation properties also limits its production and application in the electrical field. Therefore, in order to solve the problem of difficult bonding between basalt fiber and resin matrix and make up for the research blank of basalt fiber composites in insulation performance, this paper provides a basalt fiber modification method—SiO₂ coating, and tests the insulation and mechanical properties of the modified composite. We used nano-SiO₂ coating solution to modify basalt fiber, and manufactured BF/resin composite (BFRP) by hand lay-up and hot-pressing technology, and experimentally analyzed the influence of nano-SiO₂ content on the mechanical and insulation properties of the modified composite. Fourier transform infrared spectrum and scanning electron microscope analysis showed that nano-SiO₂ was successfully coated on basalt fibers. Through the microdroplet debonding test, it was found that the IFSS of fiber/resin was improved by 35.15%, 72.97 and 18.9%, respectively, after the modification of the coating solution with SiO₂ concentration of 0.5%, 1% and 1.5%, showing better interface properties; the single fiber tensile test found that the tensile strength of the modified fiber increased slightly. Among all composites, 1 wt% SiO₂ coating modified composites showed the best comprehensive properties. The surface flashover voltage and breakdown field strength reached 13.12 kV and 33 kV/mm, respectively, which were 34.6% and 83% higher than unmodified composite. The dielectric loss is reduced to 1.43%, which is 33.8% lower than the dielectric loss (2.16%) of the untreated composite, showing better insulation ability; the tensile strength, bending strength and interlaminar shear strength were increased to 618.22 MPa, 834.74 MPa and 16.29 MPa, respectively, which were increased by 53%, 42.4% and 59.7%, compared with untreated composites. DMA and glass transition temperature showed that the modified composite had better heat resistance. TGA experiments showed that the resin content of the modified composite increased, and the internal structure of the composite became denser.

As a lightweight and highly insulating composite material, epoxy resin syntactic foam is increasingly widely used for insulation filling in electrical equipment. To avoid core burning and cracking, which are prone to occur during the casting process, the epoxy resin-based syntactic foam insulation materials with high thermal conductivity and low coefficient of thermal expansion are required for composite insulation equipment. The review is divided into three sections concentrating on the two main aspects of modifying the thermal properties of syntactic foam. The mechanism and models, from the aspects of thermal conductivity and coefficient of thermal expansion, are presented in the first part. The second part aims to better understand the methods for modifying the thermal properties of syntactic foam by adding functional fillers, including the addition of thermally conductive particles, hollow glass microspheres, negative thermal expansion filler and fibers, etc. The third part concludes by describing the existing challenges in this research field and expanding the applicable areas of epoxy resin-based syntactic foam insulation materials, especially cross-arm composite insulation.

A simple and efficient process method for the preparation of strontium bismuth oxides (SBOs) via an impregnation-calcination method is presented. The synthesized active materials are characterized using X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy. The electrochemical performance of the as-synthesized SBO samples is observed to decrease gradually as the strontium content is increased from 25% to 50%. The SBO sample with a Sr/Bi ratio of 1 : 3 shows the highest specific capacitance of 1228.7 F g⁻¹ (specific capacity of 204.8 mAh g⁻¹) at a current density of 1 A g⁻¹ and a good cycling stability (75.1%) over 3000 charge-discharge cycles. The improved performance of the supercapacitors can be attributed to the unique structural features resulting from the addition of appropriate portions of Sr, which supports high electron conductivity and rapid ion/electron transport within the electrode and at the electrode/electrolyte interface. All the results show that the SBOs have considerable potential for use as high-performance battery-type electrodes in supercapacitors.

The abnormal heating of composite insulators on transmission lines frequently occurs, seriously threatening the power grid’s safe and stable operation. For different types of abnormal heating composite insulators, undifferentiated replacement wastes a lot of labor and material resources. This study explores the abnormal heating composite insulators under different environmental humidity and wind speed conditions. The heating and discharge of composite insulators are observed, and the heating range, heating shape, and temperature rise (ΔT) are analyzed. The abnormal heating of the sheath-aging composite insulator is related to the aging of the silicone rubber and the environmental humidity. The partial discharge caused by the core rod’s defect is the primary source of the temperature rise in the decay-like insulator. The heating range of the contaminated insulator is connected to the environmental humidity, and the ΔT increases with the salt density. The ΔT and heating range of the three types of abnormal heating increase with the ambient humidity. The heating phenomenon under low humidity is an important characteristic that distinguishes decay-like and contaminated insulators from sheath-aging insulators. Therefore, the on-site infrared inspection should be carried out in sunny and windless weather to prevent the impact of high humidity and wind speed on infrared temperature measurement.