This paper presents a single-coarse dual-fine architecture that improves energy-efficiency of pipelined-SAR analog-to-digital converters (ADCs). A coarse and fast sub-ADC is used to quantize the most significant bits (MSBs), which are encoded with a proposed residue transformation method to control the residue generation of the first stages in two fine channels. The residue voltages generate on the capacitive digital-to-analog converters (C-DACs) of split fine channels directly without successive approximation processes. Therefore, the conversion rate is increased and the power is reduced. A shuffle mechanism is introduced into split-ADC based digital background calibration to avoid the divergence of the conventional algorithm in the proposed architecture. A high-energy-efficiency dynamic amplifier is also introduced as the residue amplifier. A 14-bit 60-MS/s ADC is prototyped in a 28-nm CMOS process. The digital calibration engine operates under 0.9-V supply, other parts of the ADC core operate under 1.05-V supply. The ADC core consumes 4.26 mW. Measurement results show that the calibration improved the signal-to-noise and distortion ratio (SNDR) and spur-free dynamic range (SFDR) dramatically, the calibrated ADC achieves SNDR and SFDR of 66.9 dB and of 91.0 dB respectively, translating to a Schreier FoM of 165.4 dB and a Walden FoM of 39.3 fJ/conversion-step.
14 November 2024 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article introduces a successive approximation register (SAR) analog-to-digital converter (ADC) that utilizes a foreground capacitor mismatch self-calibration method. The proposed floating operation puts the uncalibrated high-bit capacitor into the floating state, preventing the sub-ADC from saturating caused by comparator static offset during the calibration process. To address the random mismatch of the LSB capacitors and improve the calibration accuracy, this article employs round-robin grouping of eight sets of LSB capacitors. In addition, a precharged bootstrapped switch is proposed to achieve high sampling linearity with low power consumption and area overhead. An anti-interference custom-designed 0.5-fF capacitor structure is suggested for binary-weighted capacitor mismatch of capacitive DAC (CDAC). Furthermore, the circuit implementation of the comparator utilized by ADC is also discussed. The prototype was fabricated in a 180-nm CMOS process with a 1.8-V supply and achieved spurious-free dynamic ranges of 108.9 and 92.38 dB at an input frequency of 1 kHz while operating at sampling rates of 100 kS/s and 1 MS/s, respectively. The prototype consumes 6.745 mW and occupies 0.91 $\text{mm}^2$ .
30 June 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief focuses on the robustness of the ring amplifier (RA), an alternative to the operational transconductance amplifier (OTA) in the deep nanoscale CMOS process. The effective gain (EG) of the RA shows diverse characteristics from the DC gain and can be treated as a non-linear gain error (NLGE). The EG shows a notable variation when taking process, supply voltage, and temperature (PVT) into consideration. An improved statistical calibration based on the back-end stage data is proposed to compensate the NLGE. A prototype SAR-assisted pipeline ADC with a quick-start RA is implemented in a 28-nm CMOS process, achieving 60.3 dB SNDR and 76.5 dB SFDR with a 6 MHz input at 625 MS/s. The SNDR and SFDR are 58.6 dB and 70.7 dB with a Nyquist input frequency and consumes 13.2 mW, achieving Walden and Schreier figure-of-merit (FoM) values of 30.4 fJ/conv.-step and 162.2 dB. For a −6 dBFS 50 MHz input, the measured SNDR and SFDR are above 55.5 dB and 68.9 dB with supply voltage and temperature fluctuation.
19 April 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
The performance of zero intermediate frequency (IF) receiver is usually limited by the frequency dependent I/Q mismatch, which gets worse with the increase of the signal bandwidth. Because the frequency dependent errors caused by the mixer and the baseband filters are difficult to eliminate, digital calibration methods are widely adopted. Among all the calibration methods, the algorithm based on the detection in frequency domain is able to extract the error at different frequencies which makes it suitable for foreground calibration. This paper proposed a receiver I/Q mismatch calibration method applied to wideband FDD transceivers, which can extract the error in frequency domain by transmitting customized signals through transmitters. A reasonable frequency plan is adopted to avoid the interference of TX image, nonlinearity and LO leakage and the wideband I/Q mismatch is compensated by a complex finite impulse response (FIR) filter. The proposed algorithm fully utilizes the existing hardware of the receiver, achieving a good balance between algorithm performance and hardware cost, which is validated on a FDD transceiver platform and the image rejection ratio (IRR) is improved from 33dB to at least 66dB in the whole baseband with a bandwidth of 245MHz.
A 2.5-GS/s 12-bit four-way time-interleaved pipelined-SAR ADC is presented in 28-nm CMOS. A bias-enhanced ring amplifier is utilized as the residue amplifier to achieve high bandwidth and excellent power efficiency compared with a traditional operational amplifier. A high linearity front-end is proposed to alleviate the non-linearity of the diode for ESD protection in the input PAD. The embedded input buffer can suppress the kickback noise at high input frequencies. A blind background calibration based on digital-mixing is used to correct the mismatches between channels. Additionally, an optional neural network calibration is also provided. The prototype ADC achieves a low-frequency SNDR/SFDR of 51.0/68.0 dB, translating a competitive of 0.48 pJ/conv.-step at 250 MHz input running at 2.5 GS/s.
22 August 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper introduces a 0.5-V, two-stage, pseudo-differential bulk-driven operational transconductance amplifier with high gain and linearity for low-power continuous-time applications. The input stage’s common-mode feedback utilizes a linear resistor detector with a conductance reduction cross-coupled pair to mitigate the loading effect of the common-mode detector resistor at ultra-low power operations. Temperature dependence of the conductance reduction circuit is compensated. The impact of the conductance reduction circuit on linearity performance is explored. The output stage employs a class-AB topology and utilizes a phase lead compensator to stabilize the OTA. Implemented in 180 nm CMOS technology, this OTA achieves a DC gain and slew rate of 68 dB and 26.1 V/ $\mu$ s, respectively, under a capacitive load of 10 pF. The total power consumption is 34.2 $\mu$ W. With unit gain feedback configuration, the measured total harmonic distortion is only 0.02% at an output amplitude of 500 mVpp. Test results validate the proposed circuit, positioning it competitively compared to state-of-the-art designs.