To control the flow separation in the compressors, a novel pulsed jet concept without external energy injection is proposed. The new concept designs a slot in the middle of the blade and sets a micro device to switch the slot periodically. Such a structure is expected to generate a pulsed jet by the pressure difference between the pressure side and the suction side of the blade. In order to analyze the interaction between the pulsed jet and unsteady separated flow, our numerical and experimental study is based on a specific cascade (with a flow separation inside) and a pulsed jet (one of the unsteady flow control method). The experimental and numerical results both show that when the frequency of pulsed jet is approximate to that of the separation vortex, then the control tends to be more effective. Based on the numerical simulations, the proper orthogonal decomposition (POD) is then used to reveal the control mechanism, extracting the different time-space structures from the original field. The results with the aid of POD show that the pulsed jet can redistribute the kinetic energy of each mode, and strengthen or weaken certain modes, particularly, while the steady jet reduces the kinetic energy of high-order modes in whole. Also, pulsed jet with proper parameters can transfer the energy from higher modes to the first flow mode (averaged flow), which is due to the conversion of the spatial vortical structures and the time evolution of the modes.
Micro turbine engine (MTE) is an important kind of propulsion system for miniature unmanned aircraft or missiles, because of its better high-speed performance (than propeller propulsion) and higher propulsion efficiency (obviously than rockets). Windmill start is a common air-starting mode used in micro turbine engine. The windmill starting characteristics are important to the practical use of micro turbine engine. In this paper, the windmill starting characteristics research for a 12 cm diameter (MTE-D) micro turbine engine is carried out by experiment and numerical simulation. The characteristic of rotor mechanical losses at low-speed condition is studied, and the engine common working line of windmill starting process is obtained. Based on the engine windmill characteristics, the propane ignition characteristics under different inflow conditions are researched, and the envelope of propane ignition and propane flameout is determined. The experimental research of fuel supply and ignition characteristics is completed, and the envelope of fuel supply and ignition is obtained. The windmill stage, propane ignition stage, fuel ignition stage and acceleration process from idling-speed to 80% full speed of MTE-D micro turbine engine is optimized, and the optimization windmill starting parameters are collected. The successful windmill starting experiment under this condition with engine speed up to 80% full speed indicates that these starting parameters are reasonable. All the starting parameters of MTE-D micro turbine engine obtained in this work are dimensionless parameters, and the conclusions obtained in this study have some reference to other micro turbine engines with the similar structural form and starting process.
High thrust and low specific fuel consumption (SFC) are important for vertical takeoff and landing (VTOL) vehicles. An effective way to decrease the SFC is to increase the bypass ratio (BPR) of the propulsion system. The air-driven fan (or fan-in-wing) has a very high bypass ratio and has proved to be successful in VTOL aircrafts. However, the tip turbine that extracts energy for the air-driven fan faces the low-solidity problem and performs inadequately. In this study, we developed a high-reaction method for the aerodynamic design of a tip turbine to solve the low-solidity problem. A typical tip turbine was selected and designed by both conventional and high-reaction methods. Three-dimensional flow fields were numerically simulated through a Reynolds-averaged Navier-Stokes (RANS)-based computational fluid dynamics (CFD) method. The energy extraction rate was proposed to evaluate and display the energy extraction capability of the turbine. The results showed that the high-reaction turbine could solve the low-solidity problem and significantly increase the isentropic efficiency from approximately 80.0% to 85.6% and improve the isentropic work by 71.9% compared with the conventional method (from 10.28 kW/kg to 17.67 kW/kg).
Origami has been inspiring roboticists to create new devices. Here, we present a preliminary design and performance test of a novel origami actuator inspired by Yoshimura pattern. This actuator is in a hexagonal configuration made of a single piece of paper. Driven by the threads, the origami actuator can bend and shorten. The design of its folding pattern is presented, and the folding procedure is also formulated. The folding pattern and paper properties contribute to the performance of the actuator. Particularly, the grammage, standing for the area density of paper as a metric to classify the paper, draws our attention. We develop a test setup to examine the impact of the grammage on the elastic property of the actuator. We found that although there was a hysteresis effect during the deformation, the origami actuator exhibited the linear elastic properties over a certain range of shortening.
1 January 2017 in Journal of Mechanical Engineering