Three-dimensional printing technology is constantly developing and has a wide range of applications; one application is electrical insulation, where the standard technology uses polymer-based filaments. Thermosetting materials (epoxy resins, liquid silicone rubbers) are broadly used as electrical insulation in high-voltage products. In power transformers, however, the main solid insulation is based on cellulosic materials (pressboard, crepe paper, wood laminates). There are a vast variety of transformer insulation components that are produced using the wet pulp molding process. This is a labor-intensive, multi-stage process that requires long drying times. In this paper, a new material, microcellulose-doped polymer, and manufacturing concept for transformer insulation components are described. Our research focuses on bio-based polymeric materials with 3D printability functionalities. A number of material formulations were tested and benchmark products were printed. Extensive electrical measurements were performed to compare transformer components manufactured using the traditional process and 3D printed samples. The results are promising but indicate that further research is still required to improve printing quality.

This article presents a comparative analysis of the crucial physical properties of electrically conductive components made of pure copper, produced by various additive manufacturing technologies such as binder jetting (BJ) and direct metal laser sintering (DMLS). The comparison concerned the assessment of critical parameters important from the application point of view, such as: electrical conductivity, hardness, yield point, microstructure and the occurrence of internal material defects. Same-sized components made in a conventional casting and subtractive method (machining) were used as a reference material. Comprehensive tests and the comparison of a wide range of parameters allowed us to determine that among the selected methods, printing using the DMLS technique allowed for obtaining arcing contact with mechanical and electrical parameters very similar to the reference element. Therefore, the obtained results showed the possibility of using the copper elements made by additive manufacturing for the switching and protection devices used in electrification and energy distribution industrial sectors.

Additive manufacturing offers great potential for various industrial solutions; in particular, the binder jetting method enables the production of components from various materials, including sand molds for casting. This work presents the results of an extensive set of experiments aimed at enhancing the structural strengthening of 3D-printed sand molds. Structural strengthening was achieved by impregnating the sand-printed structures with two polymer materials: epoxy resin and silicone varnish. Impregnation was performed with variable parameters, such as temperature, pressure, and time. Structural strengthening using polymers was investigated by analyzing the flexural strength and impact resistance of the impregnated products and comparing these obtained values with the reference material in terms of impregnation parameters and the polymer used. Microstructural observations and an analysis of the pore filling were also performed. This approach allowed for a full assessment of the influence of processing parameters and the type of polymer used for impregnation on the properties of sand-printed structures, which allowed for identifying the most optimal method to be used to strengthen the sand molds for casting the components for electrical devices. As a direct proof of concept, it was shown that impregnation with polymeric materials could effectively strengthen the sand mold, increasing its flexural strength and impact resistance by over 20 times and 5 times, respectively. A full-scale mold was printed using binder jetting, impregnated with epoxy resin at 65 °C, and used to successfully fabricate a fully functional electrification device.

In recent years, additive manufacturing (AM) has made considerable progress and has spread in many industries. Despite the advantages of this technology including freedom of design, lead time reduction, material waste reduction, special tools manufacturing elimination, and sustainability, there are still a lot of challenges regarding finding the beneficial application. In this study, the feasibility of replacing traditional manufacturing methods with additive manufacturing in the energy sector is investigated, with a specific focus on gas-insulated high-voltage switchgear (GIS). All aluminum parts in one specific GIS product are analyzed and a decision flowchart is proposed. Using this flowchart, printability and the best AM technique are suggested with respect to part size, required surface roughness, requirements of electrical and mechanical properties, and additional post processes. Simple to medium complexity level of geometry, large size, high requirements for electrical and mechanical properties, threading and sealing, and lack of a standard for printed parts in the high voltage industry make AM a challenging manufacturing technology for this specific product. In total, implementing AM as a short series production method for GIS aluminum parts may not be sufficient because of the higher cost and more complex supply chain management, but it can be beneficial in R&D cases or prototyping scenarios where a limited number of parts are needed in a brief time limit.

In the power industry, various electrically insulating materials are used to ensure proper mechanical, thermal, and dielectric performance over decades of equipment operation. In power transformers, cellulose is the predominant material in manufacturing various insulation components. Most of these products are manufactured by wet-molding technology. However, this process is long, labor-intensive, and highly energy-demanding. Under the frame of an EU-funded grant, a new kind of insulation material and manufacturing process were developed. Fully bio-based material (produced in the form of pellets) can be processed using additive manufacturing, allowing for much shorter manufacturing times for insulation products, with considerably less scrap and energy consumption (due to the elimination of the drying stage). The focus of the project was extrusion additive manufacturing technology, but at a later stage, a biomaterial powder was developed, making it possible to print with other technologies. In the paper, comparative studies on various additive manufacturing techniques of newly developed biopolymers have been presented, including extrusion, High Speed Sintering (HSS), and Selective Laser Sintering (SLS). The applicability of such material in power transformers required extensive testing of various properties. These results are discussed in the paper and include: oil compatibility, volume resistivity measurements, permittivity and dissipation factor measurements, determination of partial discharge inception voltage, partial discharges measurement, and breakdown voltage measurements. Although mechanical properties remain below industrial targets, the pioneering results provide a promising route for unique directions toward more sustainable manufacturing of high-voltage cellulose insulation and ideas for improving the material properties during the printing process.

Additive manufacturing (AM) is treated as a significant contributor to sustainability due to lower energy consumption, less material usage and reduced number of wastes generated when comparing with traditional manufacturing technologies. Currently there is a lot of commercial applications of such new technology in number of industry segments. However, such sector as high voltage engineering still struggles with number of challenges when considering additive manufacturing. In products working in high voltage environment, very often, in addition to mechanical loads there are demanding conditions, as elevated temperature and presence of insulation oil or gas. This requires a special approach to printing quality of the printed structures without internal voids and in case of metals, with improved electrical conductivity. In the paper, few examples of additive manufacturing applications in area of power products have been presented, including printed transformer insulation, printed copper, and application of AM for spare parts. For each case, the main challenges have been discussed.