This study investigates the strengthening mechanism and carbide precipitation behavior of medium Mn steel with Nb-Mo microalloy after cyclic quenching and austenite reverse transformation treatment. The results show that the Nb/Mo element not only precipitates (Nb,Mo)C in the grains, hindering the movement of dislocations and increases the strength, but also segregates at the austenite/ferrite grain boundary, thus delaying the transformation from austenite to ferrite. In addition, a large amount of nano-scale cementite is retained after cyclic quenching and austenite reverse transformation, which has a positive effect on the proportion of retained austenite in medium Mn steel. Moreover, the carbides with small size and low Mn content are dissolved, and the decomposed C and Mn content are beneficial to the nucleation of austenite during the intercritical annealing process at a temperature of 690 °C.
The study aimed to identify a moderate degree of Ce addition to improve the toughness in the simulated coarse-grained heat-affected zone (CGHAZ) of high-strength low-alloy steels, based on the effect of the Ce content on particle characteristics, microstructure and impact toughness. Three steels with 0.012 wt.%, 0.050 wt.% and 0.086 wt.% Ce content were subjected to 100 kJ/cm heat input in their thermal welding cycles. The particles and microstructures in the simulated CGHAZ of each steel were characterized and the impact-absorbance energy levels were measured at −20 °C. The results indicated that Ce2O2S inclusion compounds were gradually modified to CexSy-CeP and CeP with the increasing of the Ce content. A higher fraction of acicular ferrite was formed in the 0.012 wt.%-Ce-treated steel due to the lower mismatch between Ce2O2S and α-Fe. Furthermore, a lower fraction of M-A constituent was obtained in the 0.012 wt.%-Ce-treated steel. As a result, superior toughness and a typical amount of ductile fracture were detected in the simulated CGHAZ of the 0.012 wt.%-Ce-treated steel. Compared with the 0.012 wt.%-Ce-treated steel, a smaller prior austenite grain was observed in the 0.086 wt.%-Ce-treated steel because of the segregation of CeP at the grain boundary. However, the larger size and density of CeP led to poor toughness in the CGHAZ of the 0.086 wt.%-Ce-treated steel.
High temperature tensile properties and long-term thermal stability play an important role in practical applications of Al-Zn-Mg-Cu alloys. In order to evaluate the effect of Er addition on the properties of an Al-Zn-Mg-Cu alloy as potential high temperature structural materials, the heat resistance properties of an Al-Zn-Mg-Cu alloy were investigated at various temperatures. After high temperature tensile testing and long periods of heat exposure testing, the microstructures of Al-Zn-Cu-Mg alloys with and without small Er addition is intentionally investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and quantitative transmission electron microscopy (TEM) characterization to explore the potential effect of Er on the tensile properties. The experimental results reveal that the heat resistance of T76-tempered Al-Zn-Cu-Mg alloy is obviously improved by adding trace Er. The Al8Cu4Er phase is found to segregate at the localized regions along grain boundaries and strengthens the grain boundaries at elevated temperatures. The η′ and η precipitation is obviously promoted by adding trace Er, and dispersed nano-sized Al3(Er, Zr) precipitates were formed in the Er-containing alloys after homogenization, thereby enhancing the strength of Al-Zn-Mg-Cu. In addition, precipitates in both alloys gradually coarsen with the increase in thermal exposure temperature and the extension of thermal exposure time. The influence of precipitates on mechanical properties of the investigatived alloy after thermal exposure is also discussed.
Severe erosion wear is found on valve spools, which threatens the safety and reliability of these units. The use of the plasma beam spraying surfacing method can significantly improve the corrosion resistance and sealing performance of hydraulic valve spools, reduce material waste, and reduce maintenance costs. The effects of the co-addition of CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases, and wear property of plasma-beam-sprayed Fe55-based coatings on 1025 steel were investigated using OM, EDS, ultra-deep field microscopy, and a wet sand rubber wheel friction tester, respectively. The dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of the microstructure with the co-addition of CeO2 and SiC particles. CeO2 or SiC reduced the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of the Fe55 welding layer was Cr7C3, γ-Fe. The martensite in the surfacing layer and the carbides formed Cr7C3, which can improve the hardness of the surfacing layer. The grain boundaries consisted mainly of a reticular eutectic structure. The uniform distribution of the Cr7C3 hard phase in the Fe55+1.5 wt% SiC+0.01 wt% CeO2 resulted in a uniformly worn surface. The sub-wear mechanisms during the friction process were micro-ploughing and micro-cutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01 wt% CeO2 were well-matched, avoiding excessive micro-cutting and microplastic deformation. A low content of CeO2 could lead to the formation of equiaxed grain and effectively improve the uniformity of the microstructure. The wear-resistant layer of Fe55+1.5 wt% SiC+0.01 wt% CeO2 can effectively improve the service life and long-term sealing performance of the valve spools.
In this study, niobium was added into grain-oriented silicon steels, four Nb-bearing hot-rolled bands with Nb content range from 0–0.025 wt% were prepared and a detailed study of the micro characterization (microstructure, texture and precipitates) of hot-rolled bands was carried out by various analysis methods, such as EBSD and TEM. The results indicate that the precipitates in Nb-free steel are MnS and AlN; however, in the Nb-bearing steel they are MnS, AlN and Nb(C, N). The precipitates are finer and more dispersed in Nb-bearing steel, and a stronger pining force was obtained, which contributes to the finer microstructure and less recrystallization fractions of the hot-rolled bands. A larger volume fraction and stronger intensity of Goss texture is presented in steel with 0.025 wt% Nb due to the effective inhibiting effect. However, it has little effect on the changes of microstructure and texture when the Nb content is more than 0.009 wt%.
In order to enhance the performance of 20# steel, this study successfully fabricated AlCoCrFeNi high-entropy alloy coatings with different WC contents (x = 0, 10, 20, 30 wt%) on its surface using plasma cladding technology. The effects of WC content on the microstructure, mechanical properties, and corrosion resistance of the coatings were systematically investigated. The results indicate that without WC addition, the coating consists of a dual-phase structure comprising BCC and FCC phases. With the incorporation of WC, the FCC phase disappears, and the coating evolves into a composite structure based on the BCC matrix, embedded with multiple carbide phases such as W2C, M7C3, MxCγ, and Co6W6C. These carbides are predominantly distributed along grain boundaries. As the WC content increases, significant grain refinement occurs and the volume fraction of carbides rises. The coating exhibits a mixed microstructure of equiaxed and columnar crystals, with excellent metallurgical bonding to the substrate. The microhardness of the coating increases markedly with higher WC content; however, the rate of enhancement slows when WC exceeds 20 wt%. The hardness of 1066.36 HV is achieved at 30 wt% WC. Wear test results show that both the friction coefficient and wear rate first decrease and then increase with increasing WC content. The optimal wear resistance is observed at 20 wt% WC, with a friction coefficient of 0.549 and a wear mass loss of only 0.25 mg, representing an approximately 40% reduction compared to the WC-free coating. Electrochemical tests demonstrate that the coating with 20 wt% WC facilitates the formation of a dense and stable passive film in NaCl solution, effectively inhibiting Cl− ion penetration. This coating exhibits the best corrosion resistance, characterized by the lowest corrosion current density of 1.349 × 10−6 A·cm−2 and the highest passive film resistance of 2764 Ω·cm2.