The study of cellular structures and their properties represents big potential for their future applications in real practice. The article aims to study the effect of input parameters on the quality and manufacturability of cellular samples 3D-printed from Nylon 12 CF in synergy with testing their bending behavior. Three types of structures (Schwarz Diamond, Shoen Gyroid, and Schwarz Primitive) were selected for investigation that were made via the fused deposition modeling technique. As part of the research focused on the settings of input parameters in terms of the quality and manufacturability of the samples, input parameters such as volume fraction, temperature of the working space, filament feeding method and positioning of the sample on the printing pad were specified for the combination of the used material and 3D printer. During the experimental investigation of the bending properties of the samples, a three-point bending test was performed. The dependences of force on deflection were mathematically described and the amount of absorbed energy and ductility were evaluated. The results show that among the investigated structures, the Schwarz Diamond structure appears to be the most suitable for bending stress applications.
In the planning stage of the fabrication process of physical models of cellular structures, a surface model of the structure needs to be adjusted to acquire the requisite properties, but errors emerge frequently at this stage. The main objective of this research was to repair or reduce the impact of deficiencies and errors before the fabrication of physical models. For this purpose, it was necessary to design models of cellular structures with different accuracy settings in PTC Creo and then compare them after the tessellation process using GOM Inspect. Subsequently, it was necessary to locate the errors occurring in the process of preparing models of cellular structures and propose an appropriate method of their repair. It was found that the Medium Accuracy setting is adequate for the fabrication of physical models of cellular structures. Subsequently, it was found that within regions where mesh models merged, duplicate surfaces emerged, and the entire model could be considered as manifesting non-manifold geometry. The manufacturability check showed that in the regions with duplicate surfaces inside the model, the toolpath creation strategy changed, causing local anisotropy within 40% of the fabricated model. A non-manifold mesh was repaired in the proposed manner of correction. A method of smoothing the model’s surface was proposed, reducing the polygon mesh density and the file size. The findings and proposed methods of designing cellular models, error repair and smoothing methods of the models can be used to fabricate higher-quality physical models of cellular structures.
For the machining of long and narrow surfaces and when processing multiple pieces, planing technology is used, the productivity of which can be higher than that of milling, although it is relatively slow machining. The article aims to study the degree of influence of the geometry of the tool (the angle of cutting-edge inclination and the angle of the tool-orthogonal rake), as well as the cutting conditions (cutting depth and cutting speed) on the chip characteristics (temperature and microhardness) in orthogonal and oblique slow-rate machining of steel 1.0503 (EN C45). The experiments were carried out on specially prepared workpieces designed for immediate stopping of machining. The results of the experiments were statistically processed, and behavioural models were created for temperature and Vickers microhardness of chips for individual combinations of factors. The obtained dependencies revealed how the geometry of the cutting tool and the cutting conditions affect the temperature and microhardness in the cutting area and at the same time allowed the best conditions for both orthogonal and oblique machining to be set up.
Triply Periodic Minimal Surfaces (TPMSs) represent a progressive class of cellular materials with high potential for high-tech applications. This review provides a comprehensive analysis of TPMS architectures, linking their mathematical underpinnings and advanced CAD modeling in PTC Creo Parametric 12 with technological aspects of additive manufacturing and macroscopic mechanical response. The work critically compares dominant topologies such as Schoen Gyroid, Schwarz Diamond, and Schwarz Primitive, focusing on the differences between uniform and functionally graded (FG-TPMS) structures. From a production perspective, this study identifies key process limitations of PBF-LB/M and SLA additive technologies, in particular the issues of unsintered powder accumulation, geometric deviations, and the negative impact of surface roughness (satellite particles) on fatigue life. Analysis of mechanical behavior confirms the superiority of sheet-based modifications in kinetic energy absorption, where specifically tailored FG-TPMS topologies exhibit stable deformation plateaus and controlled, progressive failure modes under compression. The conclusion of the work summarizes established applications in biomedical engineering for the elimination of stress shielding, as well as emerging trends in the field of 4D printing and acoustic metamaterials. This review serves as a comprehensive engineering guide for the optimization and implementation of next-generation porous structures.