A novel positive-polarity electrostatic precipitator (ESP) was developed using an ionization stage (0.4 × 0.4 × 0.14 m(3) ) with 16 carbon fiber ionizers in each channel and a collection stage (0.4 × 0.4 × 0.21 m(3) ) with parallel metallic plates. The single-pass collection efficiency and clean air delivery rate (CADR) were measured by standard tests using KCl particles in 0.25-0.35 μm. Performance was determined using the Deutsch equation and established diffusion and field charging theories and also compared with the commercialized HEPA filter-type air cleaner. Experimental results showed that the single-pass collection efficiency of the ESP ranged from 50 to 95% and decreased with the flow rate (10-20 m(3) /min), but increased with the voltage applied to the ionizers (6 to 8 kV) and collection plates (-5 to -7 kV). The ESP with 18 m(3) /min achieved a CADR of 12.1 m(3) /min with a voltage of 8 kV applied to the ionization stage and with a voltage of -6 kV applied to the collection stage. The concentration of ozone in the test chamber (30.4 m(3) ), a maximum value of 5.4 ppb over 12 h of continuous operation, was much lower than the current indoor regulation (50 ppb).
23 November 2011 in Journal of the Air & Waste Management Association
A novel two-stage wet electrostatic precipitator (ESP) has been developed using a carbon brush pre-charger and collection plates with a thin water film. The electrical and particle collection performance was evaluated for submicrometer particles smaller than 0.01∼0.5 μm in diameter by varying the voltages applied to the pre-charger and collection plates as well as the polarity of the voltage. The collection efficiency was compared with that calculated by the theoretical models. The long-term performances of the ESP with and without water films were also compared in tests using Japanese Industrial Standards dust. The experimental results show that the carbon brush pre-charger of the two-stage wet ESP had approximately 10% particle capture, while producing ozone concentrations of less than 30 ppb. The produced amounts of ozone are significantly lower than the current limits set by international agencies. The ESP also achieved a high collection rate performance, averaging 90% for ultrafine particles, as based on the particle number concentration at an average velocity of 1 m/sec corresponding to a residence time of 0.17 sec. Higher particle collection efficiency for the ESP can be achieved by increasing the voltages applied to the pre-charger and the collection plates. The decreased collection efficiency that occurred during dust loading without water films was completely avoided by forming a thin water film on the collection plates at a water flow rate of 6.5 L/min/m 2 Zukeran, A. , Ikeda, Y. , Ehara, Y. , Matsuyama, M. , Ito, T. , Takahashi, T. , Kawakami, H. and Takamatsu, T. 1999. Two-Stage-Type Electrostatic Precipitator Re-entrainment Phenomena under Diesel Flue Gases. IEEE. Trans. Ind. Appl, 35: 346–351. [Crossref], [Web of Science ®] [Google Scholar] .
29 May 2012 in Journal of the Air & Waste Management Association
To remove particles in corrosive gases generated by semiconductor industries, we have developed a novel non-metallic, two-stage electrostatic precipitator (ESP). Carbon brush electrodes and grounded carbon fiber-reinforced polymer (CFRP) form the ionization stage, and polyvinyl chloride collection plates are used in the collection stage of the ESP. The collection performance of the ESP downstream of a wet scrubber was evaluated with KCl, silica, and mist particles (0.01–10 μm), changing design and operation parameters such as the ESP length, voltage, and flow rate. A long-term and regeneration performance (12-hr) test was conducted at the maximum operation conditions of the scrubber and ESP, and the performance was then demonstrated for 1 month with exhaust gases from wet scrubbers at the rooftop of a semiconductor manufacturing plant in Korea. The results showed that the electrical and collection performance of the ESP (16 channels, 400 × 400 mm2) was maintained with different grounded plate materials (stainless steel and CFRP) and different lengths of the ionization stage. The collection efficiency of the ESP at high air velocity was enhanced with increases in applied voltages and collection plate lengths. The ESP (16 channels with 100 mm length, 400 × 400 mm2 × 540 mm with a 10-mm gap) removed more than 90% of silica and mist particles with 10 and 12 kV applied to the ESP at the air velocity of 2 m/s and liquid-to-gas ratio of 3.6 L/m3. Decreased performance after 13 hours of continuous operation was recovered to the initial performance level by 5 min of water washing. Moreover, during the 1-month operation at the demonstration site, the ESP showed average collection efficiencies of 97% based on particle number and 92% based on total particle mass, which were achieved with a much smaller specific corona power of 0.28 W/m3/hr compared with conventional ESPs.
29 August 2017 in IEEE Transactions on Industry Applications
We developed a novel electrostatic air purifier using a carbon fiber brush charger combined with a metallic collection rod and an activated carbon fiber (ACF) sheet to improve the indoor air quality of passenger vehicles. The ACF sheet was used to apply electrostatic forces to move charged particles toward a collection rod and simultaneously adsorb gas. The cylindrical air purifier (diameter: 100 mm, length: 190 mm) was composed of a conductive brush charger and an electrostatic collection rod for particle removal, as well as an ACF filter for gas removal. The flow rate of the device was approximately 209-360 L/min. The novel purifier was tested in a 1-m 3 chamber with particles 0.3 μm in diameter and three gases: ammonia, acetic acid, and acetaldehyde. The gas cleaning performance of the purifier was compared with that of a commercial purifier with a high-efficiency particulate air (HEPA) filter, activated carbon pellets, and alumina balls. The clean air delivery rate (CADR) of the novel electrostatic air cleaner was 0.219 m 3 /min, 35% higher than that of the HEPA filter. The CADRs of the ESP air cleaner for the test gases were 0.25, 0.19, and 0.19 m 3 /min, respectively, indicating that the novel ESP air cleaner reduced the gases 308%, 204%, and 327%, respectively, faster than the commercial purifier.
5 July 2018 in IEEE Transactions on Industry Applications
A wet packed bed scrubber combined with dry oxidation by indirect DBD plasma for conversion of NO to NO2 and wet reduction with two reduction agents of Na2S and Na2SO3 to remove NO2 was developed at room temperature for semiconductor manufacturing industries. The design and operation parameter for the wet scrubber such as gas concentration, liquid to gas ratio, reducing agent concentration, residence time and pressure drop were investigated at 2 m3/min and 200 ppm of pure NO gas. Na2S solution was more suitable than Na2SO3 with less chemical consumption and liquid to gas ratio. Removal efficiency over 80% was achieved with liquid to gas ratio of 10 L/m3, reduction agent solution of 0.1% w/w which corresponds to ORP of -310 mV and pH of 12.3, residence time of 2 sec, and pressure drop of 25 mmAq/m, respectively. Finally, a demonstration test of the wet scrubber was conducted for 1 month with exhaust gas from perfluorinated compounds (PFCs) gas scrubber at the rooftop of a semiconductor manufacturing plant in Korea. In order to suppress H2S as byproducts of the wet scrubber, pH over 12 was carefully controlled with NaOH solution because commonly highly acid gases such as HF and HCl were fed from the manufacturing process. The NOx removal efficiency was average 83.8% which was very similar to those obtained from the lab tests. These results indicate that the combination of the dry oxidation and wet reduction method could be a promising solution to remove NOx from semiconductor manufacturing industries.
26 October 2021 in IEEE Transactions on Industry Applications
Electrostatic precipitators (ESPs) are widely used to control air pollution. However, their applications in portable air cleaners are limited owing to ozone generation during the discharging process. In this article, we developed a compact two-stage ESP that combines corona discharging and particle collection modules. The former generates an extremely small amount of ozone using dielectric film coating, whereas the latter has a large specific surface area. A polypropylene (PP) film is coated as a dielectric material on the ground electrode of the discharging module. The corona current is reduced by the PP film, which in turn reduces the ozone generation. The efficiency of atmospheric particle collection and ozone generation were evaluated by varying the flow rates and applied voltages of the four-channel discharging and roll-type collection modules. Additionally, the specific surface area of 707 m2/m3 of the roll-type collection module minimized the size of the device by increasing its integrity. The proposed ESP with PP coating exhibited the tendency of a conventional ESP that follows the Deutsch equation. All particles of size over 1 μm were removed from the atmosphere by the proposed device at a flow rate of 194.4 L/min, which is more than three times that of human breathing. Furthermore, our experimental device removed more than 50% of the ultrafine particles of size 0.3 μm without ozone generation. Therefore, the proposed device can be potentially used in portable or wearable air-cleaning devices to aid individual healthcare.