Chaoxiang Yang

Mr. Chaoxiang Yang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 September 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
CYChaoxiang Yang
Chaoxiang Yang
BHBohao Hu
Bohao Hu
LLLiangyu Lu
Liangyu Lu
ZWZekai Wang
Zekai Wang
WLWenjuan Liu
Wenjuan Liu
CSChengliang Sun
Chengliang Sun
This work proposes a miniaturized piezoelectric MEMS accelerometer based on polygonal topology with an area of only 868 × 833 μm2. The device consists of six trapezoidal cantilever beams with shorter fixed sides. Meanwhile, a device with larger fixed sides is also designed for comparison. The theoretical and finite element models are established to analyze the effect of the beam′s effective stiffness on the output voltage and natural frequency. As the stiffness of the device decreases, the natural frequency of the device decreases while the output signal increases. The proposed polygonal topology with shorter fixed sides has higher voltage sensitivity than the larger fixed one based on finite element simulations. The piezoelectric accelerometers are fabricated using Cavity-SOI substrates with a core piezoelectric film of aluminum nitride (AlN) of about 928 nm. The fabricated piezoelectric MEMS accelerometers have good linearity (0.99996) at accelerations less than 2 g. The measured natural frequency of the accelerometer with shorter fixed sides is 98 kHz, and the sensitivity, resolution, and minimum detectable signal at 400 Hz are 1.553 mV/g, 1 mg, and 2 mg, respectively. Compared with the traditional trapezoidal cantilever with the same diaphragm area, its output voltage sensitivity is increased by 22.48%.

9 October 2023 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
BHBohao Hu
Bohao Hu
WLWenjuan Liu
Wenjuan Liu
CYChaoxiang Yang
Chaoxiang Yang
LLLiangyu Lu
Liangyu Lu
ZWZekai Wang
Zekai Wang
CSChengliang Sun
Chengliang Sun
With increasing requirements for massive sound acquisition, piezoelectric MEMS microphones (PMMs) have attracted widespread attention due to the advantages of low power consumption, fast response, waterproof and dustproof. This work presents a PMM with sector-connected cantilevers, where the anchors are located at the center of a circular operating area of 0.5-mm $^{2}$ . According to theoretical analysis and finite element simulations, the proposed PMM exhibits higher sensitivity compared with conventional cantilever diaphragms fixed at the perimeter. The PMM is fabricated on a customized cavity silicon-on-insulator (CSOI) substrate with a 9.5% scandium-doped aluminum nitride (ScAlN) film. The output of the PMM assembly is amplified and filtered from 100-Hz to 20-kHz, and the measured sensitivity, minimum detectable pressure (MDP), resolution, total harmonic distortion (THD), and signal-to-noise ratio (SNR) are $-$ 37.6-dB (re: 1-V/Pa), 40-dB SPL, 40-dB SPL, 0.997%, and 54.2-dB at 1-kHz, respectively. The calculated nonlinearity of the PMM is less than 0.85% under 94-dB SPL. The receiving sensitivity and SNR of the ScAlN-based PMM are effectively improved, which shows great potential in intelligent voice acquisition and control scenarios. 2023-0110

3 February 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
XHXiaoming Huang
Xiaoming Huang
XGXiyu Gu
Xiyu Gu
CYChaoxiang Yang
Chaoxiang Yang
JDJiaqi Ding
Jiaqi Ding
XCXiang Chen
Xiang Chen
Shishang GuoShishang Guo
Shishang Guo
How to improve the sensitivity of Micro-electromechanical systems (MEMS) piezoelectric accelerometers has become a key technical problem in consumer electronics. In this paper, a multigrooved cantilever-type piezoelectric accelerometer based on composite film is manufactured to obtain high sensitivity of 4.62 mV/g, excessing typical accelerometer (3.36 mV/g). The theoretical model and finite element model are established to analyze the relationship between cantilever stiffness, stress distribution and sensitivity. The proposed accelerometers are fabricated by MEMS processes to form Mo/AlN/ScAlN/Mo piezoelectric stacks as the sensing layer. The experimental results show that the sensitivity, linearity, minimum detectable signal (MDS), and resonant frequency of the proposed piezoelectric accelerometer with multiple grooves are 4.62 mV/g, 0.99964, 0.02 g, and 15320 Hz, respectively. This new structure can provide inspiration for the design of high-sensitivity and high-linear MEMS piezoelectric accelerometers.

25 February 2025 in Journal of Applied Physics
Verified
Journal Article
Open access
YWYaxin Wang
Yaxin Wang
TYTingting Yang
Tingting Yang
CGChao Gao
Chao Gao
CYChaoxiang Yang
Chaoxiang Yang
BLBinghui Lin
Binghui Lin
CSChengliang Sun
Chengliang Sun
With the emergence of fifth-generation communication systems, filters with bandwidth (BW) >5% and center frequency >4 GHz are in urgent need. This work presents film bulk acoustic resonators (FBARs) and bulk acoustic wave (BAW) filters based on Al0.8Sc0.2N films. To obtain a better quality AlScN film, we deposited AlScN by physical vaper deposition method on metal-organic chemical vapor deposition developed AlN seed, which was deposited directly on a Si (111) substrate. Using film transfer technology combined with adopting different FBAR structures, filter topology circuits, and external circuits, a BAW filter with a minimum insertion loss of 1.819 dB, a center frequency of 5.56 GHz, a −3 dB BW of 599 MHz, and an out-of-band suppression of at least 35 dB is fabricated and presented in this work.

20 December 2024 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
CYChaoxiang Yang
Chaoxiang Yang
WLWenjuan Liu
Wenjuan Liu
YWYaxin Wang
Yaxin Wang
BHBohao Hu
Bohao Hu
LLLiangyu Lu
Liangyu Lu
CSChengliang Sun
Chengliang Sun
Scandium-doped aluminum nitride (ScAlN) can effectively improve the piezoelectric coefficient; meanwhile, the bimorph obtains a higher sensitivity per unit area than a unimorph structure, thereby greatly improving the sensitivity of MEMS sensors. This article proposes Sc0.1Al0.9N-based bimorph piezoelectric MEMS microphones with tractive structures, which generate a larger high-stress area during operation compared with conventional cantilevers based on finite element method (FEM) simulation and analytical methods. Four electrical connections are designed as components with the tractive structure on the same area of only 0.4679 mm2. The devices are fabricated on a thermal oxide silicon wafer using a nine-mask process. Acoustic measurements show that the maximum unamplified sensitivity is $353.79~\mu $ V/Pa from the combined series-parallel electrical connection, which is 75% higher than the full series electrical connection of $208.27~\mu $ V/Pa. Furthermore, the combined series-parallel electrical connection exhibits grateful performance, where both unamplified and amplified minimum detectable pressure (MDP) are 2 mPa, the signal-to-noise ratio (SNR) is 48.3 dB, and the total harmonic distortion (THD) is only 0.96% at 1 kHz. This work demonstrates a small-size, high-sensitivity piezoelectric MEMS microphone with combined series-parallel connection, which has great commercial value for future scenarios.

1 December 2025 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
CYChaoxiang Yang
Chaoxiang Yang
WLWenjuan Liu
Wenjuan Liu
YWYaxin Wang
Yaxin Wang
LLLiangyu Lu
Liangyu Lu
BHBohao Hu
Bohao Hu
CSChengliang Sun
Chengliang Sun
The demand for compact, lownoise acoustic transducers have motivated rapid advances in MEMS microphone technology. This work presents a high signal-to-noise ratio (SNR) piezoelectric MEMS microphone that utilizes a Sc ${}_{{0}.{1}}$ Al ${}_{{0}.{9}}$ N bimorph diaphragm with a windmill structure, occupying an area of only 0.3721 mm2. The diaphragm consists of four fixed-anchored beams linked by a central hub, which significantly increases the vibration displacement, effective and maximum bending stress. The fixed-anchored beams enable synchronous movement, forming a piston-like vibration mode. Fabricated on an 8-inch thermal-oxide silicon wafer using a 9-mask surface-micromachining process, the device features integrated pad routing and parallel electrical interconnections among segmented piezoelectric elements. Acoustic measurements show that the original and amplified sensitivities at 1 kHz are −70.12 dB and −35.41 dB (re 1 V/Pa), respectively. The microphone achieves an SNR exceeding 61.2 dB over the full audio band, along with a minimum detectable sound pressure of 1 mPa (34 dB SPL) and a resolution of 1 mPa. These performance metrics demonstrate the suitability of the device for low-frequency voice capture and other miniaturized acoustic sensing applications.