The application of flexible indium tin oxide (ITO-free) electrochromic devices has steadily attracted widespread attention in wearable devices. Recently, silver nanowire/poly(dimethylsiloxane) (AgNW/PDMS)-based stretchable conductive films have raised great interest as ITO-free substrate for flexible electrochromic devices. However, it is still difficult to achieve high transparency with low resistance due to the weak binding force between AgNW and PDMS with low surface energy because of the possibility of detaching and sliding occurring at the interface. Herein, we propose a method to pattern the pre-cured PDMS (PT-PDMS) by stainless steel film as a template through constructed micron grooves and embedded structure, to prepare a stretchable AgNW/PT-PDMS electrode with high transparency and high conductivity. The stretchable AgNW/PT-PDMS electrode can be stretched (5000 cycles), twisted, and surface friction (3M tape for 500 cycles) without significant loss of conductivity (ΔR/R ≈ 16% and 27%). In addition, with the increase of stretch (stretching to 10–80%), the AgNW/PT-PDMS electrode transmittance increased, and the conductivity increased at first and then decreased. It is possible that the AgNWs in the micron grooves are spread during PDMS stretching, resulting in a larger spreading area and higher transmittance of the AgNWs film; at the same time, the nanowires between the grooves come into contact, thus increasing conductivity. An electrochromic electrode constructed with the stretchable AgNW/PT-PDMS exhibited excellent electrochromic behavior (transmittance contrast from ~61% to ~57%) even after 10,000 bending cycles or 500 stretching cycles, indicating high stability and mechanical robustness. Notably, this method of preparing transparent stretch electrodes based on patterned PDMS provides a promising solution for developing electronic devices with unique structures and high performance.
The potential applications of stretchable strain sensors in wearable electronics have garnered significant attention. However, developing susceptible stretchable strain sensors for practical applications still poses a considerable challenge. The present study introduces a stretchable strain sensor that utilizes silver nanowires (AgNWs) embedded into a polydimethylsiloxane (PDMS) substrate. The AgNWs have high flexibility and electrical conductivity. A stretchable AgNW/Pat-PDMS conductive film was prepared by arranging nanowires on the surface of PDMS using a simple rod coating method. Depending on the orientation angle, the overlap area between nanowires varies, resulting in different levels of separation under a given strain. Due to the separation of the nanowire and the change in current path geometry, the variation in strain resistance of the sensor can be primarily attributed to these factors. Therefore, precision in strain regulation can be adjusted by altering the angle θ (0°, 60°, or 90°) of the nanowire. At the same time, the stability of the AgNW/Pattern-PDMS (AgNW/Pat-PDMS) conductive film application was verified by preparing a sandwich structure PDMS/AgNW/Pat-PDMS stretchable strain sensor. The sensor exhibited high sensitivity within the operating sensing range (gauge factor (GF) of 15 within ~120% strain), superior durability (20,000 bending cycles and 5000 stretching cycles), and excellent response toward bending.
In this paper, ZnCo2O4(Nd–ZnCo2O4) films were prepared using a hydrothermal method and an electrodeposition method. We characterized the samples using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The effect of Nd–ZnCo2O4 doping on the stability of the materials was studied. The results show that the Nd−ZnCo2O4 prepared in the experiment presents a porous network structure, no other impurity peaks and impurity elements exist, and the purity is high. In the experiment, the electrochemical properties of Nd−ZnCo2O4 were studied. When the current density is 3 A·g−1, the specific capacitance F·g−1 of the electrode is 1982 F·g−1. When the current density is changed 100 times, and every time it is changed back to 3 A·g−1, the specific capacitance F·g−1 is 1973 F·g−1, which is 99.5% of the initial specific capacitance F·g−1. 1982 F·g−1 indicates that Nd−ZnCo2O4 has good stability and can be reused many times. In the cycle stability performance test of Nd–ZnCo2O4//CNTs devices, when the current density is 3 A·g−1, the specific capacitance is 180 F·g−1. After 10,000 cycle charge discharge tests, the specific capacitance F·g−1 becomes 162 F·g−1, maintaining 90% of the initial specific capacitance. These results show that the electrode material has a long cycle life and good cycle stability.
Ce-modified MnCo2O4 flower-like nanosheet electrodes were prepared on nickel foam by a hydrothermal-calcination route and sequentially optimized with respect to reaction time, nominal Ce content, and PVP addition. Comparative SEM, XRD, XPS, and N2-sorption analyses identify MnCo2O4-9 h-3%Ce-PVP as the optimized electrode, with an open hierarchical nanosheet network and a BET surface area of 210.0 m2 g−1. The direct XRD/XPS control comparison distinguishes Ce-associated lattice and surface-state changes from PVP-associated synthesis effects without treating either trend as proof of substitutional Ce occupancy or quantitatively established oxygen vacancies. Likewise, PVP is treated as a morphology-directing additive whose transient adsorption or bridging role remains a synthesis hypothesis rather than a directly verified molecular mechanism. The optimized positive electrode delivers 2008 F g−1 at 1 A g−1, retains 1227 F g−1 at 20 A g−1, and shows 99.0% capacitance retention after 10,000 cycles at 5 A g−1. A carbon-supported iron oxide negative electrode, designated C/Fe2O3 only as a sample label because its exact oxide phase was not independently resolved by XRD or Raman spectroscopy, provides 443 F g−1 at 1 A g−1. The resulting charge-balanced asymmetric device operates over 0–1.6 V and delivers 34.6 F g−1 at 1 A g−1, corresponding to 12.30 Wh kg−1 at 0.8 kW kg−1. At 10 A g−1, it retains 29.8 F g−1 and delivers 10.60 Wh kg−1 at 8.0 kW kg−1, equivalent to 86.1% capacitance retention over a tenfold increase in current density. All device-level gravimetric values are calculated using the total active mass of both electrodes.
A charge-balanced aqueous hybrid supercapacitor was constructed by coupling Co-modified MnWO4 nanorods with H2O2-treated carbon nanotubes (OH-CNTs) in 1 M KOH. The samples were designated by the nominal Co/(Mn + Co) precursor molar fraction; ICP-OES measured bulk Co fractions of 0.09 ± 0.01, 0.47 ± 0.03, and 0.75 ± 0.04 mol% for the nominal 0.1, 0.5, and 0.8 mol% samples, respectively. Rietveld refinement confirmed retention of the monoclinic P2/c MnWO4 phase with only small composition-dependent lattice changes. At an active-material loading of 2.00 ± 0.05 mg cm−2, the optimized nominal 0.5 mol% sample delivered 429.5 ± 11.0 C g−1 (119.3 ± 3.1 mAh g−1) at 1 A g−1 and retained 280.5 ± 8.5 C g−1 (77.9 ± 2.4 mAh g−1) at 15 A g−1. Because the positive electrode exhibits battery-type behavior, specific charge and specific capacity are used as the primary performance descriptors. Over −0.9–0 V vs. SCE, pristine CNT and OH-CNT electrodes delivered of 189.0 ± 7.2 and 246.6 ± 8.1 C g−1, corresponding to electrode-level apparent specific capacitances of 215 ± 8 and 280 ± 9 F g−1 at 1 A g−1 after correction for the measured IR drop. These values apply to the stated 90:5:5 CNT (or OH-CNT)/acetylene-black/PVDF formulation and CNT-active-mass normalization and should not be interpreted as intrinsic capacitances of isolated commercial MWCNT powders. Charge matching based on the measured gave m+/m− = 0.574; integration at the actual device loadings yielded q+ = 0.861 ± 0.015 C and q− = 0.854 ± 0.015 C (q+/q− = 1.008). The device operated over 0–1.6 V and delivered 97.9 ± 3.1 F g−1 at 0.51 A g−1, corresponding to 34.8 Wh kg−1 at 408 W kg−1 when normalized to the combined active mass of both electrodes. Three independently assembled devices retained 96.0 ± 0.7% of the initial capacitance and showed a coulombic efficiency of 98.8 ± 0.1% at the 10,000th cycle at 5.13 A g−1. Device metrics are normalized to the combined active mass of both electrodes and exclude current collectors, separator, electrolyte, and packaging.
Hydrogen sensing is of great significance for environmental monitoring and safety due to the low explosion limit and high flammability of hydrogen gas. In this work, layered and bulk Ni-MOF precursors are designed and pyrolyzed to obtain Ni-Layer-Pyrolysis and Ni-Bulk-Pyrolysis materials. Structural characterizations reveal that Ni-Layer-Pyrolysis inherits a layered morphology with a core–shell structure, higher graphitization degree, and more uniform active sites compared with its bulk counterpart. Electrochemical studies demonstrate that Ni-Layer-Pyrolysis exhibits lower charge-transfer resistance and higher carrier density, which facilitate efficient electron transport. Gas-sensing tests show that the Ni-Layer-Pyrolysis sensor achieves a low detection limit of 100 ppm, a sensitivity of 6.24 at 8000 ppm H2. Moreover, it displays excellent selectivity against common interfering gases and outstanding long-term stability over 40 days. These results indicate that the layered structure and core–shell architecture play a decisive role in enhancing sensitivity, selectivity, and durability. This study provides new insights into the design of MOF-derived nanostructures for high-performance hydrogen sensors with practical application potential.