In order to study the protection performance of silane coating on in-service concrete structures in a sulfate environment, we collect concrete samples in the field to simulate the concrete erosion process by accelerated erosion with wetting–drying cycles. We place the samples into protected, exposed and control groups corresponding to a corrosive environment with silane protection, corrosive environment without protection and general environment for three different service conditions. A combination of ultrasonic velocimetry, CT (Computed Tomography) scan imaging, NMR (Nuclear Magnetic Resonance) pore structure analysis, strength testing and other methods are used to analyze the strength, ultrasonic wave velocity, pore structure and other characteristics of the specimens during sulfate erosion. Based on the test results, the protective effect of silane coating on concrete structures under sulfate attack is quantitatively analyzed, and an index for judging the damage rate of specimens is proposed to quantitatively analyze the protective effect of silane coating. The research results show that the damage of the concrete structure under silane protection in a sulfate-attack environment can be reduced by more than 50%; its integrity damage index and strength damage index are easily affected by the location of local defects, which leads to a decrease in the protection efficiency of the surface silane coating.
The corrosion of concrete in sulfate environments is a difficult problem in the durability of civil engineering structures. To investigate the variability of deterioration damage to concrete structures by sulfate erosion under non-destructive testing and quantify the protective effect of silane coatings on concrete under the action of sulfate erosion, an accelerated erosion experiment was carried out using field sampling in a tunnel project under a sulfate erosion environment. By means of ultrasonic velocity measurement and CT scanning, the samples protected by a silane coating under the sulfate attack environment were compared with those not protected. The deterioration characteristics of concrete under the sulfate attack environment and the protective effect of silane coating on the concrete structure were analyzed. In addition, a method for evaluating the sulfate damage to concrete based on CT images and ultrasonic velocity analysis was proposed. The results show that the samples prepared in the field show a significant difference in ultrasonic velocity in the process of erosion and deterioration according to the material difference at the measuring point interface. Through the overall damage evaluation analysis of the sample, it is concluded that the damage degree of the protected group sample is light and the heterogeneity is weak, whereas the local damage to the exposed group is serious. Combined with the CT image analysis of concrete before and after loading, the distribution characteristics of the damaged area divided by the concrete sulfate damage evaluation method proposed in this paper are highly similar to the real situation. The results of the study can provide a reference for similar projects for the detection, analysis, protection and evaluation of sulfate-attacked concrete.
When buildings are exposed to erosion from the natural environment, erosion behaviors such as surface damage and structural instability occur, which greatly affect the aesthetic value and service life of the buildings. The study of erosion behaviors and the establishment of a suitable erosion model are constructive references for the protection and restoration of buildings. In order to establish a suitable erosion model for architectural red sandstone, two types of red sandstone specimens were selected in this paper to carry out dry and wet cycle tests. Combining the theoretical analysis and the actual erosion situation, a unidirectional corrosion model is proposed to describe the erosion of buildings by the natural environment. In this model, it is assumed that only the outer surface of the building is in contact with external erosion factors for a long period of time, so this situation can be considered a unidirectional erosion process. The paper uses XRD, SEM, and ultrasonic methods to record changes in the properties of the red sandstone samples. Finally, the rationality of the unidirectional erosion model was verified numerically. The test results show that the red sandstone specimens subjected to erosion by the natural environment will be accompanied by the development of defects, such as cracks, fissures, and holes, as well as the generation of fresh material. The demarcation point of different erosion stages exists in both the in-service red sandstone specimens and the fresh red sandstone specimens, which is consistent with the results of the unidirectional erosion model. In this paper, a calculation model for the demarcation point of different erosion stages is established, and the model estimation shows that the demarcation point of different erosion stages of the in-service red sandstone sample is 1.1528 cm from the erosion surface, and the demarcation point of different erosion stages of the fresh red sandstone sample is 1.67 cm.
The properties and appearance of ancient architectural red sandstone will be damaged after being eroded by the natural environment for a long time. In order to investigate the weathering and erosion characteristics of the red sandstone structure of an existing ancient building, ultrasonic testing techniques, combined with scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray computed tomography (X-CT), were used to analyze a building in Ganzhou. The variation in chemical substances contained in the red sandstone specimens according to phenology was analyzed by X-ray diffraction (XRD). The characteristic parameters of the CT grayscale images of the red sandstone were extracted and combined with the ultrasonic wave velocity values to comprehensively analyze the degradation characteristics of the red sandstone specimens, and a method to characterize the degradation degree of the red sandstone as a whole plane is proposed. We use the gray model (GM (1, 1)) to predict the surface degradation degree of red sandstone specimens, and gray relation analysis (GRA) to further analyze the correlation between the characteristic parameters of CT grayscale images of red sandstone and its degradation degree. The results show that in the natural erosion environment, dolomite and chlorite are generated on the exposed surface of the red sandstone, which can protect the internal sandstone to a certain extent. The degradation degree of the red sandstone specimens in the horizontal X and Y directions varies, and the proposed method of calculating the overall plane degradation degree of the red sandstone is feasible. The minimum average relative error of the surface degradation degree obtained from the gray prediction GM (1, 1) model is 1.4591%. There is a good correlation between the characteristic parameters of the red sandstone CT grayscale images and the degradation degree.
15 November 2024 in Journal of Civil Structural Health Monitoring