Sotya Astutiningsih

Dr. Sotya Astutiningsih

Metallurgical and Materials Engineering, Universitas Indonesia, Depok, Jawa Barat, Indonesia
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2023 in Buildings
Verified
Journal Article
Open access
PDF file
EEEristra Nungsatria Tresna Ernawan
Eristra Nungsatria Tresna Ernawan
JSJessica Sjah
Jessica Sjah
NHNURAZIZ HANDIKA
NURAZIZ HANDIKA
SASotya Astutiningsih
Sotya Astutiningsih
EVEric Vincens
Eric Vincens
This study aimed to analyze the mechanical, displacement, and strain properties of concrete with Ferronickel Slag (FNS) fine aggregate substitute (0%, 50%, and 100%, by mass, later called FNS-0, FNS-50, and FNS-100, respectively) experimentally using the Digital Image Correlation (DIC) method and the Ultrasonic Pulse Velocity (UPV) test. The FNS used in this study is a by-product that came from a Ferronickel smelter in Indonesia coupled with manufactured sand (M-sand) as the fine aggregate control. A D10 × 20 cm3 cylinder and 15 × 15 × 15 cm3 cube specimens were used to analyze the density, compressive strength, and UPV. Additionally, the cube specimens were tested using the DIC method to analyze the displacement and strain properties. The test results show the highest compressive strength was obtained by FNS-50, followed by FNS-100 and FNS-50. The highest pulse velocity was obtained by FNS-100, followed by FNS-50 and FNS-0. The load–displacement response and strain behavior indicate the specimen that had the most load resistance was FNS-50, followed by FNS-100 and FNS-0. Poisson’s ratio obtained using DIC and strain gauges showed consistent results where FNS-0 had the highest values, followed by FNS-50 and FNS-100. Overall, concrete with FNS substitute showed higher density, compressive strength, pulse velocity, and stiffness, as well as lower Poisson’s ratio compared to control concrete (FNS-0).

13 August 2021 in Atom Indonesia
Verified
Journal Article
Closed access
MHM. W. Hasan
M. W. Hasan
SSS. Sugiharto
S. Sugiharto
SASotya Astutiningsih
Sotya Astutiningsih

5 October 2022 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
MSMuhammad Saukani
Muhammad Saukani
ALAyu Novia Lisdawati
Ayu Novia Lisdawati
Heri IrawanHeri Irawan
Heri Irawan
RIRendy Muhamad Iqbal
Rendy Muhamad Iqbal
DNDwi Marta Nurjaya
Dwi Marta Nurjaya
SASotya Astutiningsih
Sotya Astutiningsih
Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 g, 5 g, 10 g, and 15 g. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

27 April 2018 in International Journal of Technology
Verified
Journal Article
Open access
JMJackson Muliawan
Jackson Muliawan
SASotya Astutiningsih
Sotya Astutiningsih
Phosphate Sludge (PS) waste has been a problem in metal surface finishing industry. The waste cannot be dumped in landfill due to the metal content. Valorisation of the waste will be beneficial in a way that it conserves natural reserves and reduces energy consumption. This paper describes the attempt of utilization of PS by mixing it in kaolin in preparation of ceramic bricks. A series of experiments showed that mixtures containing between 25–50 mass % PS sintered at 1200oC attained the highest compressive strength of >25 MPa. X-ray diffractions (XRD) showed that the presence of PS hindered the formation of mullite, the phase that contribute to strength in Al2O3–SiO2 kaolin system. In the mixture of 1:1 kaolin: PS fired at 1200oC, cristobalite was formed, instead of mullite, as observed in the XRD patterns.

20 June 2023 in International Journal of Renewable Energy Development
Verified
Journal Article
Open access
PDF file
CRChristin Rina Ratri
Christin Rina Ratri
QSQolby Sabrina
Qolby Sabrina
TLTitik Lestariningsih
Titik Lestariningsih
ANAdam Febriyanto Nugraha
Adam Febriyanto Nugraha
SASotya Astutiningsih
Sotya Astutiningsih
Mochamad ChalidMochamad Chalid
Mochamad Chalid
Dielectric behavior of cellulose-based polymer electrolyte was studied at various temperature and salt concentration. A polymer electrolyte membrane based on cellulose acetate (CA) as the polymer host and LiClO4 as the dopant salt was fabricated using the solution casting technique. The dopant salt concentration was varied as 0.3, 0.5, 0.67, and 1M. Dielectric relaxation spectroscopy characterization were performed using potentiostat at frequency ranging from 0.1 Hz to 1 MHz. Measurements were performed by sandwiching the membrane between stainless steel plates. The ionic conductivity was then calculated based on the Cole–Cole plot obtained from the impedance measurement. It was found that sample 1 M had the highest ionic conductivity at high frequencies. However, the frequency-dependent conductance plot showed that the ionic conductivity of the 1 M sample significantly decreased at low frequencies, i.e. from 3.41×10-5 S/cm at 1 MHz to 1.9×10-8 S/cm at 0.1 Hz. Other samples did not experience this phenomenon, including those with a Celgard© commercial membrane to represent commercial Li-ion batteries. This is caused by excess charge accumulation, leading to a high concentration of immobile charge carriers, which reduces the available free volume surrounding the polymer chain. This resulted in a significant decrease in ionic conductivity at low frequencies. Temperature variation was also performed on the conductivity measurement at 30-70 °C. Temperature variation showed more predictable behavior, where increasing the temperature activated charge carriers and enhanced ionic conductivity, from 1.81×10-5 S/cm at room temperature to 9.04×10-5 at 70°C. Sweeping across the frequency range results in a consistent sequence of ionic conductivities among the samples at various temperatures. This work is beneficial for evaluating a biomass-based polymer electrolyte complex in a Li-ion battery environment. Feasibility studies can be performed at various concentrations and temperatures to determine the optimal level of dopant salt input across a broad frequency range.

22 August 2025 in Cleaner Waste Systems
Verified
Journal Article
Open access
SASotya Astutiningsih
Sotya Astutiningsih
DODasi Agung Ospaman
Dasi Agung Ospaman
NHNURAZIZ HANDIKA
NURAZIZ HANDIKA
DWDwica Wulandari
Dwica Wulandari