This article reports the electrospinning technique for the manufacturing of multilayered scaffolds for bile duct tissue engineering based on an inner layer of polycaprolactone (PCL) and an outer layer either of a copolymer of D,L-lactide and glycolide (PLGA) or a copolymer of L-lactide and ε-caprolactone (PLCL). A study of the degradation properties of separate polymers showed that flat PCL samples exhibited the highest resistance to hydrolysis in comparison with PLGA and PLCL. Irrespective of the liquid-phase nature, no significant mass loss of PCL samples was found in 140 days of incubation. The PLCL- and PLGA-based flat samples were more prone to hydrolysis within the same period of time, which was confirmed by the increased loss of mass and a significant reduction of weight-average molecular mass. The study of the mechanical properties of developed multi-layered tubular scaffolds revealed that their strength in the longitudinal and transverse directions was comparable with the values measured for a decellularized bile duct. The strength of three-layered scaffolds declined significantly because of the active degradation of the outer layer made of PLGA. The strength of scaffolds with the PLCL outer layer deteriorated much less with time, both in the axial (p-value = 0.0016) and radial (p-value = 0.0022) directions. A novel method for assessment of the physiological relevance of synthetic scaffolds was developed and named the phase space approach for assessment of physiological relevance. Two-dimensional phase space (elongation modulus and tensile strength) was used for the assessment and visualization of the physiological relevance of scaffolds for bile duct bioengineering. In conclusion, the design of scaffolds for the creation of physiologically relevant tissue-engineered bile ducts should be based not only on biodegradation properties but also on the biomechanical time-related behavior of various compositions of polymers and copolymers.

Transfer of regenerative approaches into clinical practice is limited by strict legal regulation of in vitro expanded cells and risks associated with substantial manipulations. Isolation of cells for the enrichment of bone grafts directly in the Operating Room appears to be a promising solution for the translation of biomedical technologies into clinical practice. These intraoperative approaches could be generally characterized as a joint concept of tissue engineering in situ. Our review covers techniques of intraoperative cell isolation and seeding for the creation of tissue-engineered grafts in situ, that is, directly in the Operating Room. Up-to-date, the clinical use of tissue-engineered grafts created in vitro remains a highly inaccessible option. Fortunately, intraoperative tissue engineering in situ is already available for patients who need advanced treatment modalities.

Reliable methods for identifying rodents play an important role in ensuring the success of preclinical studies. However, animal identification remains a trivial laboratory routine that is not often discussed, despite the fact that more than 6 million rodents are used in animal studies each year. Currently, there are extensive regulations in place to ensure adequate anesthesia and to reduce animal suffering during experiments. At the same time, not enough attention is paid to the comfort of rodents during routine identification procedures, which can be painful and cause some complications. In order to achieve the highest ethical standards in laboratory research, we must minimize animal discomfort during the identification phase. In this article, we discuss traumatic methods of identification and describe several painless methods for marking in long-term experimental studies. The use of non-traumatic and non-invasive methods requires the renewal of marks as they fade and additional handling of the rodents. Laboratory personnel must be trained in stress-minimizing handling techniques to make mark renewal less stressful.

Insufficient vascular growth in the area of artificial-material implantation contributes to ischemia, fibrosis, the development of bacterial infections, and tissue necrosis around the graft. The purpose of this study was to evaluate angiogenesis after implantation of polycaprolactone microfiber scaffolds modified by a pCMV-VEGF165-plasmid in rats. Influence of vascularization on scaffold degradation was also examined. We investigated flat microfibrous scaffolds obtained by electrospinning polycaprolactone with incorporation of the pCMV-VEGF-165 plasmid into the microfibers at concentrations of 0.005 ng of plasmid per 1 mg of polycaprolactone (0.005 ng/mg) (LCGroup) and 0.05 ng/mg (HCGroup). The samples were subcutaneously implanted in the interscapular area of rats. On days 7, 16, 33, 46, and 64, the scaffolds were removed, and a histological study with a morphometric evaluation of the density and diameter of the vessels and microfiber diameter was performed. The number of vessels was increased in all groups, as well as the resorption of the scaffold. On day 33, the vascular density in the HCGroup was 42% higher compared to the control group (p = 0.0344). The dose-dependent effect of the pCMV-VEGF165-plasmid was confirmed by enhanced angiogenesis in the HCGroup compared to the LCGroup on day 33 (p-value = 0.0259). We did not find a statistically significant correlation between scaffold degradation rate and vessel growth (the Pearson correlation coefficient was ρ = 0.20, p-value = 0.6134). Functionalization of polycaprolactone by incorporation of the pCMV-VEGF165 plasmid provided improved vascularization within 33 days after implantation, however, vessel growth did not seem to correlate with scaffold degradation rate.

Treatment of a wide variety of defects in the oral and maxillofacial regions requires the use of innovative approaches to achieve best outcomes. One of the promising directions is the use of gene-activated materials (GAMs) that represent a combination of tissue engineering and gene therapy. This approach implies that biocompatible materials will be enriched with gene-carrying vectors and implanted into the defect site resulting in transfection of the recipient’s cells and secretion of encoded therapeutic protein in situ. GAMs may be presented in various designs depending on the type of material, encoded protein, vector, and way of connecting the vector and the material. Thus, it is possible to choose the most suitable GAM design for the treatment of a particular pathology. The use of plasmids for delivery of therapeutic genes is of particular interest. In the present review, we aimed to delineate the principle of work and various designs of plasmid-based GAMs and to highlight results of experimental and clinical studies devoted to the treatment of periodontitis, jaw bone defects, teeth avulsion, and other pathologies in the oral and maxillofacial regions.

Soft gingival tissue deficiency remains a severe problem leading to postoperative recession, peri-implantitis, and bone resorption. The use of collagen matrices does not always lead to complete rebuilding of the gingiva volume. The application of mesenchymal stromal cells (MSCs) simultaneously with collagen materials represents a promising approach for the restoration of soft gingival tissues. However, short-term effects of MSCs-enriched collagen grafts after gingival augmentation have not yet been studied properly. Mucograft and Mucoderm matrices were implanted in rabbits (n = 12) simultaneously with the intraoperative injection of rabbit bone marrow-derived mesenchymal stromal cells (BM-MSCs) or without cells. Collagen matrices were implanted under the flap or by the surface technique without intentional primary closure. The samples were harvested seven days after implantation, histological staining with hematoxylin and eosin, and immunohistochemical staining for VEGF, IGF1, and TGF were performed. The use of Mucoderm led to better augmentation outcomes on day 7 compared with Mucograft (p < 0.0001). Gingival augmentation in combination with the local administration of BM-MSCs led to better regeneration of the soft gingival tissues independently of the type of implanted collagen matrices (p < 0.0001). Furthermore, injection of BM-MSCs significantly enhanced gingival vascularization and epithelization with a clear positive correlation between vascular growth and epithelial response. Administration of BM-MSCs in combination with various collagen materials may potentially improve gingiva regeneration.