Muhammad Waqas Hanif

Mr. Muhammad Waqas Hanif

Industrial Engineering, University of Engineering and Technology Taxila, Rawalpindi, Punjab, Pakistan
orcid
Researcher

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 December 2022 in China Foundry
Verified
Journal Article
Closed access
PDF file
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
AWAhmad Wasim
Ahmad Wasim
MSMuhammad Sajid
Muhammad Sajid
SHSalman Hussain
Salman Hussain
MJMuhammad Jawad
Muhammad Jawad
MJMirza Jahanzaib
Mirza Jahanzaib

29 September 2024 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
FHFeroz Haider
Feroz Haider
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
MJMirza Jahanzaib
Mirza Jahanzaib

14 November 2024 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
MSMuhammad Sajid
Muhammad Sajid
MJMuhammad Jawad
Muhammad Jawad
WAWasim Ahmad
Wasim Ahmad

22 January 2025 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
MWMuhammad Waseem
Muhammad Waseem
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
MJMuhammad Jawad
Muhammad Jawad
SHSalman Hussain
Salman Hussain

13 June 2023 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
FHFeroz Haider
Feroz Haider
MJMirza Jahanzaib
Mirza Jahanzaib
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
It is a requirement of modern age industries, especially the aerospace, automobile, and shipbuilding sectors, to manufacture high strength and low weight dissimilar aluminium alloy welded joints. Therefore, the aim of this project is to investigate the effect of tool rotation speed, feed rate, and pin type on the ultimate tensile strength (UTS) of dissimilar aluminium alloys (2024 Al and 5754 Al) in friction stir welded joints. Nine experiments have been performed using an orthogonal array (L9) of the Taguchi method. An analysis of variance (ANOVA) established that pin type is the most prominent parameter, followed by tool rotation speed and feed rate. The optimal value of ultimate tensile strength (268 MPa) was achieved at 1.5 mm/s feed rate, 1600 rpm speed, and type 1 of pin. A confirmation test shows that there is a high correlation between the estimated and actual values of UTS.

20 September 2022 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
AWAhmad Wasim
Ahmad Wasim
MSMuhammad Sajid
Muhammad Sajid
The present study aims to evaluate the effect of process parameters such as melt temperature (MT), squeeze pressure (SP) and insert pre-heating temperature (IPT) on the ultimate tensile strength (UTS) of an AA7075-Cu overcast joint using an orthogonal array (L8) of Taguchi techniques. The analysis of variance (ANOVA) test results showed that SP is the most significant process parameter due to the significant reduction in air gaps between aluminum and copper. The optimal value of UTS (39.33 MPa) was attained at higher levels of SP (90 MPa), MT (800 °C) and IPT (300 °C). The confirmation test validated the significance of process parameters in optimizing the UTS of an AA7075-Cu overcast joint due to the low percentage error.
1