Feroz Haider

Mr. Feroz Haider


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2024 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
FHFeroz Haider
Feroz Haider
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
MJMirza Jahanzaib
Mirza Jahanzaib

13 June 2023 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
FHFeroz Haider
Feroz Haider
MJMirza Jahanzaib
Mirza Jahanzaib
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
It is a requirement of modern age industries, especially the aerospace, automobile, and shipbuilding sectors, to manufacture high strength and low weight dissimilar aluminium alloy welded joints. Therefore, the aim of this project is to investigate the effect of tool rotation speed, feed rate, and pin type on the ultimate tensile strength (UTS) of dissimilar aluminium alloys (2024 Al and 5754 Al) in friction stir welded joints. Nine experiments have been performed using an orthogonal array (L9) of the Taguchi method. An analysis of variance (ANOVA) established that pin type is the most prominent parameter, followed by tool rotation speed and feed rate. The optimal value of ultimate tensile strength (268 MPa) was achieved at 1.5 mm/s feed rate, 1600 rpm speed, and type 1 of pin. A confirmation test shows that there is a high correlation between the estimated and actual values of UTS.

20 September 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
FHFeroz Haider
Feroz Haider
MJMuhammad Jawad
Muhammad Jawad
AAAsad Ali
Asad Ali
AIAsif Imran
Asif Imran
This paper focuses on the multi-objective optimization of friction stir welding process parameters. Three input variables, including the axial load (AL), tool rotation speed (RS), and tool tilt angle (TA), were selected to optimize the mechanical characteristics of Al-2024 friction stir-welded (FSW) joints. The ultimate tensile strength (UTS) and impact energy (IE) were selected as output responses to measure the mechanical characteristics of Al-2024 FSW joints. A total of nine experiments, using the L9 orthogonal array as part of the Taguchi method, were performed to determine the significance of the process parameters. Gray relational analysis (GRA) was employed to conduct the multi-objective optimization of these combinations of process parameters. The results of the analysis of variance (ANOVA) showed that the AL has the most significant effect on the UTS and IE of Al-2024 FSW joints, followed by the TA and RS. The Taguchi-based GRA analysis revealed that an AL of 10 KN, a TA of 2 degrees, and an RS of 1500 rpm resulted in an optimal UTS of 333.06 MPa and an IE of 40.62 Joules. In these optimal experimental settings, optical microscopy analysis revealed the presence of a recrystallized fine-grain structure in the heat-affected zone of the welded region.

7 September 2023 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
AIAsif Imran
Asif Imran
Muhammad Waqas HanifMuhammad Waqas Hanif
Muhammad Waqas Hanif
MSMuhammad Sajid
Muhammad Sajid
SSShahab Salim
Shahab Salim
FHFeroz Haider
Feroz Haider
MAMuhammad Azeem
Muhammad Azeem
In this research work, machining operations on an aluminum matrix composite (AMC) were optimized for improving the wear of high-speed steel tools. The squeeze casting method was used to manufacture the AMC, which had Al-6061 as matrix material and silicon carbide (wt. 15%) microparticles used as reinforcement. Feed rate (Fr), cutting speed (Cs), and depth of cut (Dc) were selected to optimize HSS tool wear rate. Using the Box–Behnken design, seventeen experiments were performed to analyze the single-factor effects and interaction effects of the process parameters on HSS tool wear rate. Experimental results show that optimal tool wear (0.964) was achieved at a Cs of 80 m/min, Fr of 0.2 rev/min, and Dc of 0.8 mm.