Rongguang Wang

Prof. Dr. Rongguang Wang

Department of Mechanical Systems Engineering, Hiroshima Institute of Technology, Hiroshima, Japan
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 June 2023 in Coatings
Verified
Journal Article
Open access
PDF file
ZXZhefeng Xu
Zhefeng Xu
WYWang yan
Wang yan
XGXiaomin Gao
Xiaomin Gao
LPLuya Peng
Luya Peng
QQQi Qiao
Qi Qiao
JYJinku Yu
Jinku Yu
The corrosion resistance of FeCoNiCr high-entropy alloy deposits was investigated upon being prepared by current electrodeposition. The coatings were co-deposited in an electrolyte of an aqueous ferrous, cobalt, nickel, and chromium sulfates solution. Energy dispersive spectrometry analysis demonstrated that all four elements were co-deposited successfully. At the same time, the results from SEM indicate that the surface of the coating exhibits a granular morphology, with uniform density and no presence of cracks, with sizes ranging from 500 nm to 5 μm. Furthermore, X-ray diffraction patterns enunciated that the as-deposited coatings were amorphous. The polarization curves of the FeCoNiCr high-entropy alloy coating were measured by an electrochemical workstation in 3.5 wt.% NaCl, 1 mol·L−1 H2SO4 and 1 mol·L−1 NaOH solutions. The results revealed that the coating exhibited excellent corrosion resistance. The corrosion mechanism of the FeCoNiCr high-entropy alloy coating was analyzed in different environments. Moreover, the scratch testing method was employed to determine the alloy adhesion on the substrate, with higher values obtained for the FeCoNiCr alloy.

11 September 2019 in Scientific Reports
Verified
Journal Article
Open access
PDF file
Rongguang WangRongguang Wang
Rongguang Wang
YLYunhui Li
Yunhui Li
TXTian Xiao
Tian Xiao
LCLi Cong
Li Cong
YLYunhan Ling
Yunhan Ling
MBMohammed Bazzaoui
Mohammed Bazzaoui
Employing atomic force microscopy (AFM) to measure passive film thickness on stainless steel (SS) in aqueous solution is proposed. SUS304 austenite and SUS329J4L duplex SS samples partly covered by gold were set in a minicell. To remove the original film, the SS surface but gold was etched using dilute sulfuric acid. After cleaning, open circuit potential (OCP), and distance from the sample surface to the top of the gold were measured. They were then immersed in either 1.0% NaCl; 5.0% NaCl; or aqueous solution with pH ranging from 1.0 to 10.0 and measured again. Differences between the first and subsequent measures of OCP suggested a passive film had formed in solution with pH ranging from 2.8 to 10.0. Similarly, differences among AFM measures revealed the observed film thickness increased with increase in pH and with decrease in chloride ions. Also, film thickness in water was greater than that in a vacuum. Comparison of AFM measurements of passive film on the austenite and sigma phases in sensitized SUS329J4L duplex SS revealed the film was thinner on the sigma phase containing more chromium. Taken together, these findings suggest the proposed method is applicable for measuring the thickness of passive films in aqueous solution.

13 March 2018 in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
Verified
Journal Article
Open access
Rongguang WangRongguang Wang
Rongguang Wang
MIMasanobu Imagawa
Masanobu Imagawa
MHMasaharu Honda
Masaharu Honda
TMTakayuki Mori
Takayuki Mori
HFHideki Fukuhara
Hideki Fukuhara
Sigma phase generally precipitates in duplex stainless steel during slow cooling, which usually causes loss in both corrosion resistance and fracture toughness. To develop a non-destructive method to detect the sigma phase in duplex stainless steel for in situ use in the quality management of large structures, the double-loop electrochemical potentiokinetic reactivation behaviour of continuously cooled duplex stainless steel SUS329J4L at different cooling rates was investigated under different conditions. The polarisation condition with the solution of 0.5 M H2SO4 + 0.01 M KSCN + 0.5 M NaCl and the potential scanning rate of 0.83 mV s−1 were determined as suitable and sensitive. This paper is part of a supplementary issue from the 17th Asia-Pacific Corrosion Control Conference (APCCC-17).

4 January 2002 in Scripta Materialia
Verified
Journal Article
Closed access
Rongguang WangRongguang Wang
Rongguang Wang
MTMutsumi Takeda
Mutsumi Takeda
MKMitsuo Kido
Mitsuo Kido

1 May 2018 in Polymer Testing
Verified
Journal Article
Closed access
AJA. El Jaouhari
A. El Jaouhari
SJS. Ben Jadi
S. Ben Jadi
ZAZ. Aouzal
Z. Aouzal
MBM. Bouabdallaoui
M. Bouabdallaoui
EBE.A. Bazzaoui
E.A. Bazzaoui
MBM. Bazzaoui
M. Bazzaoui

1 January 2012 in Tetsu-to-Hagane
Verified
Journal Article
Open access
KNKeijiro Nakasa
Keijiro Nakasa
Rongguang WangRongguang Wang
Rongguang Wang
AYAkihiro Yamamoto
Akihiro Yamamoto
TSTsunetaka Sumomogi
Tsunetaka Sumomogi