This study investigates the modeling of surface roughness (Ra) in the laser cutting of EN 10130 steel process by integrating classical statistical and machine learning methods. First, a quadratic model was developed using response surface methodology (RSM) based on a Box–Behnken experimental design with 17 runs, using cutting speed, laser power, and auxiliary gas pressure as input parameters. Although the RSM model achieved an R2 value of 0.8227, there were still some nonlinear deviations between the predicted and experimental values. To improve the prediction accuracy, a regression tree algorithm was applied to model the residuals of the RSM output. The resulting hybrid model, which combines RSM predictions with machine learning-based corrections, yielded a higher R2 of 0.8889 and a lower RMSE compared to the original RSM model. A leave-one-out cross-validation (LOOCV) was performed to evaluate the generalization, which resulted in an RMSE of 0.3241 and an R2 of 0.6039. These findings confirm the effectiveness of the hybrid approach in capturing complex dependencies and improving prediction accuracy, highlighting its potential for advanced process modeling in laser machining.
One of the most important challenges for every machining shopfloor, especially a small one, is to achieve the required productivity with minimal energy consumption and engaged power. The paper presents a way to determine the optimal combination of values of cutting parameters such as depth of cut, feed rate and cutting speed from the range of their recommended values, which are usually additionally limited by the real conditions of available machines and tools. The optimal combination is the one which ensures targeted productivity and maximum energy savings at the same time. As an example, a real practice case of external rough turning of an AISI 1045 steel workpiece is presented. The selection of the optimal combination of cutting parameter values is based on a model which is developed using in situ measurements of energy consumption and engaged power in an experiment that emulates the critical operation in terms of energy consumption. The results show that optimization of cutting parameter values that enables the minimum of total energy consumption while achieving target productivity, does not necessarily enable the maximum of energy savings for a given operation. In the example from real practice shown in the paper, this optimization approach can cause higher total energy consumption by as much as 15.9% compared to the combination of parameters that ensure maximum productivity.
Turning is a complex machining process that can be characterized by a number of performances for a given machining system, workpiece material, cutting tool, and selected cutting regime. In addition to the characteristics of the machined surface quality, the estimation of machining time is particularly important for manufacturers, since machining time is directly related to other important performances of the turning process, such as productivity, cost, and energy consumption. In this paper, a model for estimation of total operation time in turning of a part with continuous profile, made of polyoxymethylene copolymer (POM-C), using a polycrystalline diamond (PCD) cutting tool, was developed. Face centred central composite design (CCD) and Box–Cox transformation approaches were applied for that purpose. The developed model was then used as the objective function in the proposed optimization model, which also included three practical constraints related to quality of the machined surface (surface roughness and workpiece deflection) and machinability aspects of the workpiece material (favourable chip forms). Nonlinear and linear models, used as constraints, were developed based on the results of experimental investigation of turning of POM-C using a PCD cutting tool. The total operation time estimation model showed good agreement with the results of tool path simulations in CAM software and validation experimental trial in real manufacturing environment. By applying the optimal solution, 44% of the total time being saved for machining of a single part can be achieved, compared to the recommended cutting parameter values, which indicates significant optimization benefits in turning industrial plastics.
Satellite data have the potential to significantly enhance railway operations and drive the digitization of the rail sector. In the context of railways, satellite data primarily refers to the use of Global Navigation Satellite System (GNSS) data for applications such as navigation, positioning, and signalling. However, remote sensing data from Earth Observation (EO) satellites remain comparatively underutilized in railway applications. While the use of GNSS data in railways is well documented in the literature, research on EO-based remote sensing methods remains relatively limited. This paper aims to bridge this gap as it presents a comprehensive review of the use of satellite data in railway applications, with a particular focus on the underexplored potential of EO data. It provides the first in-depth analysis of EO techniques, primarily examining the use of synthetic aperture radar (SAR) and optical satellite data for key applications for infrastructure managers and railway operators, such as assessing track stability, detecting deformations, and monitoring surrounding environmental conditions. The goal of this review is to explore the diverse range of EO-based applications in railways and to identify emerging trends, including the integration of thermal EO data and the novel use of SAR for dynamic and predictive analyses. By synthesizing existing research and addressing knowledge gaps, the presented review underscores the potential of EO data to transform railway infrastructure management. Enhanced spatial resolution, frequent revisit cycles, and advanced AI-driven analytics are highlighted as key enablers for safer, more reliable, and cost-effective solutions. This review provides a framework for leveraging EO data to drive innovation and improve railway monitoring practices.
29 August 2020 in The International Journal of Advanced Manufacturing Technology
Considering the complexity of laser cutting technology, and difficulties and limitations when applying traditional multi-criteria decision-making (MCDM) methods, this study proposes a fuzzy MCDM methodology for the analysis of the fibre laser cutting process, assessment of alternative cutting conditions and selection of favourable cutting conditions. The experiment in fibre laser cutting of mild steel was based on a Box–Behnken design by considering three input parameters (focus position, cutting speed and oxygen pressure) and four relevant criteria for the assessment of cutting conditions (kerf width on a straight and curved cut, surface roughness and surface productivity). The proposed fuzzy MCDM methodology makes use of expert knowledge and experimental data for criteria evaluation and decision matrix development, respectively, while three fuzzy MCDM methods (fuzzy TOPSIS, fuzzy WASPAS and fuzzy ARAS) were used to determine the complete ranking of alternatives. Kendall’s tau-b and Spearman’s rho correlation tests were applied to compare the obtained ranking lists, while the stability of the ranking was assessed with the application of the Monte Carlo simulation. Finally, to approximate the fuzzy decision-making rule, a second-order model was developed to reveal the significance of process parameters and identify favourable laser cutting conditions.