Thiago Melanda Mendes

Dr. Thiago Melanda Mendes


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2017 in Cerâmica
Verified
Journal Article
Open access
PDF file
TMThiago Melanda Mendes
Thiago Melanda Mendes
WRW. L. Repette
W. L. Repette
PRP. J. Reis
P. J. Reis
The use of nanoparticles in ultra-high strength concretes can result in a positive effect on mechanical performance of these cementitious materials. This study evaluated mixtures containing 10 and 20 wt% of silica fume, for which the optimum nano-silica content was determined, i.e. the quantity of nano-silica that resulted on the higher gain of strength. The physical characterization of raw materials was done in terms of particle size distribution, density and specific surface area. Chemical and mineralogical compositions of materials were obtained through fluorescence and X-ray diffraction. The mechanical performance was evaluated by compressive strength, flexural strength and dynamic elastic modulus measurements. The microstructural analysis of mixtures containing nano-silica was performed by X-ray diffraction, thermogravimetry, mercury intrusion porosimetry and scanning electron microscopy. Obtained results indicate an optimum content of nano-silica of 0.62 wt%, considering compressive and flexural strengths. This performance improvement was directly related to two important microstructural aspects: the packing effect and pozzolanic reaction of nano-silica.

26 August 2016 in Acta Scientiarum. Technology
Verified
Journal Article
Open access
PDF file
TMThiago Melanda Mendes
Thiago Melanda Mendes
LGLeonardo Guerra
Leonardo Guerra
GMGilson Morales
Gilson Morales
Basalt waste added to Portland cement

1 June 2016 in Cerâmica
Verified
Journal Article
Open access
TMThiago Melanda Mendes
Thiago Melanda Mendes
GMG. Morales
G. Morales
PRP. J. Reis
P. J. Reis
Nowadays, environmental codes restrict the emission of particulate matters, which result in these residues being collected by plant filters. This basaltic waste came from construction aggregate plants located in the Metropolitan Region of Londrina (State of Paraná, Brazil). Initially, the basaltic waste was submitted to sieving (< 75 μm) and the powder obtained was characterized in terms of density and particle size distribution. The plasticity of ceramic mass containing 0%, 10%, 20%, 30%, 40% and 50% of basaltic waste was measured by Atterberg method. The chemical composition of ceramic formulations containing 0% and 20% of basaltic waste was determined by X-ray fluorescence. The prismatic samples were molded by extrusion and fired at 850 °C. The specimens were also tested to determine density, water absorption, drying and firing shrinkages, flexural strength, and Young's modulus. Microstructure evaluation was conducted by scanning electron microscopy, X-ray diffraction, and mercury intrusion porosimetry. Basaltic powder has similar physical and chemical characteristics when compared to other raw materials, and contributes to ceramic processing by reducing drying and firing shrinkage. Mechanical performance of mixtures containing basaltic powder is equivalent to mixtures without waste. Microstructural aspects such as pore size distribution were modified by basaltic powder; albite phase related to basaltic powder was identified by X-ray diffraction.

1 December 2019 in Revista IBRACON de Estruturas e Materiais
Verified
Journal Article
Open access
PDF file
TMThiago Melanda Mendes
Thiago Melanda Mendes
WRW. L. Repette
W. L. Repette
The use of nano-particles is a current trend that may play an important role for improving the mechanical performance of Portland cement. The aim of this study is to evaluate the effect of nano-silica on Portland cement matrix. The particle size distribution of Portland cement matrix was modified by the incorporation of 11, 6.2, 3.1, 1.7, 0.85 and 0.42 wt.% of nano-silica. The water demand and the consumption of dispersant were adjusted, and the rheological properties of suspensions were analyzed through rotational rheometry. The mechanical performance of studied mixtures was evaluated by the compressive strength. The pore size distribution was measured by mercury intrusion porosimetry (MIP), and the hydration was analyzed through X-ray diffractometry. The rheological behavior presented a considerable changed, as a consequence of high specific surface area of nano-particles. The optimum content of nano-silica, or the smaller quantity of nano-particles, that leads to the maximum strength gain, varied according to the water to solids ratio. An increasing on the hydration and a pore refinement were obtained due to the use of silica nanoparticles. The particle’s packing and the pozzolanic reaction were the two main effects of nano-silica on the microstructure of Portland cement matrix.

14 June 2021 in Acta Scientiarum. Technology
Verified
Journal Article
Open access
PDF file
TMThiago Melanda Mendes
Thiago Melanda Mendes
WRWellington Longuini Repette
Wellington Longuini Repette
For a controlled particle size distribution, nano-silica was added to three different cements. The chemical and mineralogical compositions of the cements were characterized by fluorescence and X-ray diffraction. The granulometric distributions of cements and nano-silicas were obtained by laser granulometry and dynamic lightning scattering. The specific surface area of the raw materials was determined by gas adsorption. The effect of nano-silica and type of cement on rheological behavior was evaluated by rotational rheometry. The mechanical performance was investigated through the compression strength. The microstructural analysis was performed by scanning electron microscopy. The water demand and the consumption of dispersant increases according to the nano-silica content. The reduction in the inter-particle separation, and the agglomeration of nano-silica led to an increase in the viscosity of the suspension. The mechanical performance was directly affected by the specific surface area of the cements. Microstructural analysis showed that nano-silica changed from a layered adsorbed structure, to a porous or agglomerated structure.

1 January 2023 in Revista IBRACON de Estruturas e Materiais
Verified
Journal Article
Open access
TMThiago Melanda Mendes
Thiago Melanda Mendes
Marcelo Henrique Farias de MedeirosMarcelo Henrique Farias de Medeiros
Marcelo Henrique Farias de Medeiros
This study evaluates the effects of three carbon nanotubes with different geometric characteristics on the rheological behaviour and mechanical performance, as well as on the microstructure of mortars and cement pastes. For nanotube content ranging from 0.025 to 0.2 wt%, the yield stress and viscosity were determined by rotational rheometry, and mechanical performance was evaluated by flexural strength and dynamic modulus of elasticity. The microstructural analysis was performed by X-ray diffraction, thermo-gravimetric analysis and scanning electron microscopy (SEM). The obtained results showed that the yield stress presents a considerable increase as the carbon nanotube content increases. The viscosity was also influenced by the presence of carbon nanotubes. The flexural strength of mortars increases for different amounts of carbon nanotubes, and depending on the geometric characteristics of the carbon nanotubes, the material behaves like a composite. The microstructural analysis showed the nucleation of hydration products on the surface of the carbon nanotubes, and that the better mechanical performance of matrices containing carbon nanotubes is not related to the increase in hydration products.