1 November 2020 in Journal of Cleaner Production
1 November 2017 in Revista IBRACON de Estruturas e Materiais
The effect of alkali concentration and curing temperature regime on fly ash-based geopolymer pastes was investigated in this study by using NaOH solutions. Prismatic specimens were molded, cured at 65 °C and 85 °C and submitted to flexural and compressive strength tests. Unreacted fly ash and geopolymers were characterized by X-ray diffraction and thermogravimetric analysis. In general, the mechanical strength was enhanced by increasing the molar concentration and the curing temperature. This trend was confirmed by thermogravimetric data. However, for a lower amount of NaOH there were no significant differences between the strength results. The mixture with the highest strength was obtained with the 16 M NaOH solution and curing temperature of 85 °C, which resulted in flexural strength of 4.20 MPa, compressive strength of 21.35 MPa and also the highest weight loss of 9.89%.
1 January 2020 in Matéria (Rio de Janeiro)
The study of silanes and polymers with special functions is increasing and the development of materials from silane-based polymers follows this trend. In this way, the hydrolysis of 3-Glycidoxypropyltrimethoxysilane (GPTMS) was studied as a function of the hydrolysis time in solutions with 50% of alcoholic solvents by infrared spectroscopy. It was verified that it was possible to analyze qualitatively and quantitatively the chemical reactions involving the hydrolysis / condensation of GPTMS and the main kinetics variations during the process. The results suggest that up to 30 minutes of hydrolysis, the predominant reactions are hydrolysis of the alkoxy groups, with the generation of the Si-OH groups and alcohol, in this case methanol. From 30 minutes, there is a large amount of silanols in the solution that tend to condense and form siloxane groups, which has this reaction accelerated from 60 minutes. Already, from 70-80 minutes, the reactions tend to decrease the kinetics, due to the absence of silanols and the hydrolysis / condensation process.
1 January 2020 in Matéria (Rio de Janeiro)
This work deals with the effect in fresh and hardened properties of nano-TiO2 as addition in cement-based mortars. Three commercial nano-TiO2 powders were characterized by laser granulometry, XRD, FRX, zeta potential, BET and SEM. Two cementitious mortars were produced with nano-TiO2, an industrialized and a non-industrialized type; then, these mortars were characterized by flowability, surface roughness, flexural strength and surface fracture. The results showed that the nano-TiO2 addition reduced the flowability in terms of spread on table of the mortars. For surface roughness, in the industrialized mortars, the nanoparticles resulted in a smoother surface, while in the non-industrialized mortars, the nanoparticles formed a rougher surface. For flexural strength, in the non-industrialized mortars, the higher the nanoparticles amount, the higher the strength, while in the industrialized mortars no tendency was verified. In addition, from SEM analysis, it was noted that the fracture of the samples presented a tortuous aspect and growth through the region between cement paste and aggregates.
1 January 2010 in Matéria (Rio de Janeiro)
Neste trabalho é apresentado um estudo sobre o efeito da adição da sílica ativa (SA), nanossílica (NS) e aditivo dispersante policarboxílico (SP) sobre o comportamento reológico de pastas de cimento (CP V ARI RS). Para fins comparativos com a pasta de referência (REF), foram produzidas pastas com SA, em diferentes teores em massa (0 a 10%) e pastas com 1,0% de NS. Em todas as pastas estudadas (REF, SA e NS) variou-se SP entre 0 a 0,5%, relativos à massa de cimento. Os ensaios foram realizados em um reômetro com geometria de cilindros concêntricos e taxa máxima de cisalhamento aplicada de 100 s-1. Os aumentos de SP causaram a redução na área de histerese, na viscosidade plástica e na tensão de escoamento, sendo esta última mais influenciada que a viscosidade plástica. Nas pastas cujos resultados foram ajustados por Bingham, as misturas contendo um mesmo teor SP, a tensão de escoamento de Bingham não variou substancialmente, exceto nas pastas com 10% de SA e 0.1 a 0.3% de SP. Para a viscosidade plástica não foi observada tal tendência. Entretanto, NS influenciou significativamente o valor da viscosidade plástica em relação à REF e à SA. Nas pastas cujos resultados apresentaram aproximação satisfatória quando ajustados ao modelo de Bingham e Herschel-Bulkley, para uma mesma dosagem de SA, os aumentos nos teores de SP causaram redução na tensão de escoamento e na viscosidade plástica. O modelo de Bingham descreve adequadamente o comportamento reológico das misturas com a tensão de cisalhamento com valores intermediários, enquanto que o modelo de Herschel-Bulkley é mais adequado para as tensões máxima de cisalhamento elevadas ou reduzidas.
1 December 2019 in Revista IBRACON de Estruturas e Materiais
The use of nano-particles is a current trend that may play an important role for improving the mechanical performance of Portland cement. The aim of this study is to evaluate the effect of nano-silica on Portland cement matrix. The particle size distribution of Portland cement matrix was modified by the incorporation of 11, 6.2, 3.1, 1.7, 0.85 and 0.42 wt.% of nano-silica. The water demand and the consumption of dispersant were adjusted, and the rheological properties of suspensions were analyzed through rotational rheometry. The mechanical performance of studied mixtures was evaluated by the compressive strength. The pore size distribution was measured by mercury intrusion porosimetry (MIP), and the hydration was analyzed through X-ray diffractometry. The rheological behavior presented a considerable changed, as a consequence of high specific surface area of nano-particles. The optimum content of nano-silica, or the smaller quantity of nano-particles, that leads to the maximum strength gain, varied according to the water to solids ratio. An increasing on the hydration and a pore refinement were obtained due to the use of silica nanoparticles. The particle’s packing and the pozzolanic reaction were the two main effects of nano-silica on the microstructure of Portland cement matrix.