We present an extensive analysis of an optical Blass-matrix architecture as a beamforming network with potential for multi-beam operation in wireless systems. Its design relies on the use of phase shifters and Mach-Zehnder Interferometers (MZIs) inside an M$\times$N matrix, and enables the generation of M beams by N-element antenna arrays. We start our analysis from an optical signal with amplitude modulation by discrete microwave tones, and confirm the possibility to translate its optical phase shifts inside the matrix into equivalent phase shifts in the microwave domain. We show this is possible when the input is an optical single-side band signal and the optical carrier is re-inserted before photodetection. We extend the conclusions to the case of an optical signal carrying a microwave with quadrature amplitude modulation (QAM) and the case of simultaneous inputs at the M input ports. Based on this analysis, we propose a Blass-matrix configuration algorithm taking into account the properties of the MZIs. Through simulations, we validate the potential for multi-beam operation, and evaluate the beamforming performance at 28.5 GHz with respect to the QAM order, symbol rate and pulse shaping parameters. In all cases with rate up to 3 Gbaud, the bit-error rate remains lower than 10-3, showing that the beam squinting effect, which is present in our design, can be tolerated. Finally, we study the frequency dependence of the beamforming performance due to inevitable asymmetries of the MZIs and length variations of the waveguides, and evaluate the impact of the imperfections in the couplers inside the MZIs and the phase shifters. We show that in all cases the performance degradation is negligible for realistic fabrication and operation conditions.

We demonstrate a broadband and continuously tunable 1×4 optical beamforming network (OBFN), based on the hybrid integration of indium phosphide (InP) components in the silicon nitride (Si ₃ N ₄ ) platform. The photonic integrated circuit (PIC) comprises a hybrid InP-Si ₃ N ₄ external cavity laser, a pair of InP phase modulators, a Si ₃ N ₄ optical single-sideband full carrier (SSBFC) filter followed by four tunable optical true time delay lines (OTTDLs), and four InP photodetectors. Each OTTDL consists of eight cascaded thermo-optical micro-ring resonators (MRRs) that impose tunable true time delay on the propagating optical signals. The OBFN-PIC is designed to facilitate the steering of a microwave signal with carrier frequency up to 40 GHz over a continuous set of beam angles. We evaluate the performance of the OBFN-PIC to handle and process microwave signals, measuring the link gain, the noise figure (NF), and the spurious-free dynamic range (SFDR) parameters. Moreover, we assess its beamforming capabilities assuming that the OBFN-PIC is part of a wireless system operating in the downlink direction and feeds a multi-element antenna array. Using microwave signals at 5 and 10 GHz with quadrature amplitude modulation (QAM) formats at 500 Mbaud, we evaluate the performance of the OBFN-PIC under various configurations. We show that error-free performance can be achieved at both operating frequencies and for all the investigated beam angles ranging from 45° to 135°, thus validating its potential for high-quality beamforming performance.

We extend our previous simulation study and we present experimental results regarding our Fast Fourier Transform method for the calculation of the resonance shifts in biosensors based on micro-ring resonators (MRRs). For the simulation study, we use a system model with a tunable laser at 850 nm, an MRR with 1.5∙10⁴ quality factor, and a detection system with 50 dB maximum signal-to-noise ratio, and investigate the impact on the system performance of factors like the number of the resonance peaks inside the scanning window, the wavelength dependence of the laser power, and the asymmetry of the transfer functions of the MRRs. We find that the performance is improved by a factor of 2 when we go from single- to four-peak transfer functions, and that the impact of the wavelength dependence of the laser power is very low. We also find that the presence of asymmetries can lead to strong discontinuities of the transfer functions at the edges of the scanning window and can significantly increase the measurement errors, making necessary the use of techniques for their elimination. Using these conclusions, we build a system with sensing MRRs on TriPleX platform, and we experimentally validate our method using sucrose solutions with different concentrations. Involving techniques in order to exclude the noise originating from the microfluidic system, we achieve a wavelength resolution close to 0.08 pm, when the system operates with 0.5 pm scanning step. In combination with the sensitivity of the MRRs, which is measured to be equal to 93.7 nm/RIU, this wavelength resolution indicates the possibility for a limit of detection close to 8.5·10⁻⁷ RIU, which represents to the best of our knowledge a record performance for this type of optical sensors and this level of scanning steps.

We propose a novel concept for the implementation of 2-dimensional (2D) optical phased arrays (OPAs) with end-fire waveguides as antenna elements (AEs), and we present its theoretical model and experimental proof. The concept is based on the use of 3-dimensional (3D) photonic integrated circuits (PICs) with multiple waveguiding layers on the PolyBoard platform. In their simplest form, the 3D PICs comprise AEs at different layers, vertical and lateral couplers for the distribution of light among the AEs, and phase shifters for the execution of the 2D beam scanning process. Using the field equivalence principle, we model the radiated field from the single-mode waveguide of the platform at 1550 nm, and we find that the expected beam width is 12.7°. We also investigate the perturbation that is induced into propagating fields inside parallel waveguides in proximity, and we conclude that waveguide spacings down to 6 µm can be safely used for development of uniform OPAs in the PolyBoard platform. For OPAs with 6 µm pitch and 4 AEs, we find that the maximum steering angle is 14.0° and the expected angular clearance, wherein the main radiation lobe is higher than any grating lobe by at least 3, 6 and 10 dB is 10.8°, 7.6° and 2.8°, respectively. Based on our simulations, we design and fabricate single- and 2-layer PICs with 1 × 4 and 2 × 4 OPAs. The lateral pitch of the OPAs ranges from 10 down to 6 µm, while the vertical pitch is 7.2 µm. We experimentally characterize these OPAs and validate the potential of the 2-layer PICs for 2D beam scanning on the azimuthal and elevation plane. The beam profiles and the main scanning parameters such as the maximum steering angle and the relative intensity between the main and the grating lobes are found in excellent agreement with our simulations.

We propose an optical beamforming network (OBFN) for multi-beam operation and continuous selection of the beam angles. The OBFN is based on the use of wavelength-division multiplexing elements for the generation and manipulation of the signals that correspond to different beams and different antenna elements (AEs), and on the use of optical delay lines for the introduction of tunable time delays to these signals. We analyze the operating principle of the proposed OBFN in the downlink and uplink directions of a wireless system, and we experimentally demonstrate its proof of concept in the downlink direction up to the photodetection stage, using a 2 × 4 setup based on commercial components. The implemented OBFN has the potential to support the steering of two beams and the excitation of four AEs. Using microwave signals with 15-GHz carrier frequency, high-order modulation formats, and symbol rates up to 1 Gbaud, we modulate two optical carriers and investigate the performance of the OBFN in four experimental cases, employing different combinations of signals, steering angles, and antenna excitation schemes. Through the analysis of the expected radiation pattern and off-line measurements of the BER of the decoded signals at the intended steering angles, we validate the feasibility of the proposed OBFN. The vision for actual implementations of the proposed OBFN would be enabled by means of photonic integration techniques.

We demonstrate a 2 × 100 Gb/s transmitter and a 4 × 100 Gb/s receiver as the key components for multi-100-GbE and 400-GbE optical interfaces in future intradata center networks. Compared to other approaches, the two devices can provide significant advantages in terms of number of components, simplicity, footprint, and cost, as they are capable of serial operation with nonreturn-to-zero on-off keying format directly at 100 Gb/s. The transmitter is based on the monolithic integration of a multimode interference coupler with two Mach-Zehnder modulators on an electro-optic polymer chip, and the hybrid integration of this chip with an InP laser diode and two multiplexing and driving circuits. The receiver on the other hand is based on the hybrid integration of a quad array of InP photodiodes with two demultiplexing circuits. Combining the two devices, we evaluate their transmission performance over standard single-mode fibers without dispersion compensation and achieve a BER of 10 ^-10 after 1000 m and a BER below 10 ^-8 after 1625 m at 2 × 80 Gb/s, as well as a BER below 10 ^-7 after 1000 m at 2 × 100 Gb/s. Future plans including the development of tunable 100 GbE interfaces for optical circuit-switched domains inside data center networks are also discussed.