Novel glass samples with the composition 75TeO2–5Ta2O5–15Nb2O5–5x (where x = ZnO, MgO, TiO2, or Na2O) in mole percent were prepared. The physical, optical, and gamma radiation shielding properties of the glass samples were studied over a wide energy spectrum ranging between 0.015 and 20 MeV. The glasses’ UV–vis spectra were utilized to evaluate the optical energy gap and refractive index. Glass samples had a refractive index ranging from 2.2005 to 2.0967. The results showed that the sample doped with zinc oxide (ZnO) recorded the highest density (ρglass), molar polarizability (αm), molar refraction (Rm), refractive index (n), and third-order nonlinear optical susceptibility (χ3) and the lowest optical energy gap (Eopt) among the samples under investigation. When comparing the current glass system with various standard glass shielding materials, the prepared glass system showed superior shielding performance at energies ranging between 40 and 85 keV. These findings indicate that the prepared glass systems can be used in diagnostic X-rays, especially in dental applications.
In this study, the X-ray and gamma attenuation characteristics and optical properties of a synthesized tellurite–phosphate–sodium oxide glass system with a composition of (85 − x)TeO2–10P2O5–xNa2O mol% (where x = 15, 20, and 25) were evaluated. The glass systems we re fabricated by our research group using quenching melt fabrication. The shielding parameters of as-synthesized systems, such as the mass attenuation coefficient (MAC), linear attenuation coefficient (LAC), effective atomic number (Zeff), half-value layer (HVL), tenth value layer (TVL), mean free path (MFP), and effective electron density (Neff) in a wide energy range between 15 keV and 15 MeV, were estimated using well-known PHY-X/PSD software and recently developed MIKE software. Herein, the optical parameters of prepared glasses, such as molar volume (VM), oxygen molar volume (VO), oxygen packing density (OPD), molar polarizability (), molar refractivity (Rm), reflection loss (RL), and metallization (M), were estimated using MIKE software. Furthermore, the shielding performance of the prepared glasses was compared with that of commonly used standard glass shielding materials. The results show that the incorporation of sodium oxide into the matrix TeO2/P2O5 with an optimum concentration can yield a glass system with good shielding performance as well as good optical and physical properties, especially at low photon energy.
The thermal and optical properties of 60TeO2-20K2TeO3-10WO3-10Nb2O5 (in mol%) glasses doped with Ho2O3, Er2O3, and Tm2O3 were explored in the present work. The thermal stability, refractive index n, extinction coefficient k, absorption coefficient α, and optical band gap of the glasses were evaluated. The UV–Vis–NIR absorption spectra, the Judd–Ofelt intensity parameter, the spectroscopic quality factor, and the emission and absorption cross-sections were calculated to investigate the effects of Er3+ and Tm3+, respectively, on the band spectroscopic properties of Ho3+ ions. The results showed that the maximum emission cross-section was approximately , and the values of the full width at half maximum (, quality factor (, and gain coefficient of Ho3+: 5I75I8 were also reported. The value of the was , which showed greater gain characteristics than earlier study results. For mid-infrared solid-state lasers, the glasses that were examined might be a good host material.
In the optical energy gap, visible and near-IR emission of halide phosphate glasses with a composition of 40P2O5-30ZnO-20LiCl-10BaF2 in mol% doped with 3.5 × 104 ppm Pr2O3, referred to as PZLBPr, were synthesized. The UV-VIS-NIR and spectroscopic properties of these glasses were also predicted. The current glasses had broadband emission photoluminescence covering a wavelength range of 1250 to 1700 nm when excited at 455 nm. These bands for near-infrared emission luminescence relate to the transitions 1G4 → 3H5, 1D2 → 1G4, and 3H4 → 3F3, 3F4 in the optical telecommunication window. The significant PL emission wideband was caused by the radiative transition from Pr3+: 1D2 to 1G4. At 445 nm excitation, these glasses exhibited emission bands that corresponded to blue/reddish orange spectral ranges in visible ranges. The prepared glass has a high lasing quality factor (Ω4/Ω6 = 0.9), high optical energy (4.72 eV), and quantum efficiency = 87.3% with FWHM = 156 nm of transition emission from the 1D2 → 1G4 level. As a result, broadband near infrared optical amplifiers can be fabricated from the prepared glasses.
In this present work, we demonstrated a spectral characterization of copper–iron (Cu-Fe) alloy using optical emission spectroscopy. The Cu-Fe alloy plasma was generated on the target sample surface by directing the laser pulse of Q-switched Nd: YAG of the second harmonic (2ω) with a 532 nm optical wavelength. The optical emission spectrum was acquired using five miniature spectrometers that lie within the wavelength range of 200–720 nm. The emission plasma was characterized by validating the local-thermodynamical equilibrium (LTE) as well as optically thin (OT) plasma condition. In addition, the LTE condition was verified using the McWhirter criterion, and the OT condition was validated by comparing theoretically calculated intensity ratios with experimental ones. Plasma parameters, including electron number density as well as plasma temperature, were estimated. In the first stage, the plasma temperature was estimated using the Boltzmann-plot method and the two-line method. The average calculated value of the plasma temperatures were 8014 ± 800 K and 8044 ± 800 K using the Boltzmann-plot and two-line methods, respectively. In the second stage, electron number density was estimated using the Saha–Boltzmann equation and stark-broadening method (SBM). The average number density calculated from the SBM was and from the Saha–Boltzmann equation was , showing a good agreement. Finally, the comparative compositional analysis was performed using CF-LIBS, Boltzmann Intercept Method, EDX, and ICP-AES, which showed good agreement with that of the standard composition.
Micro/nano structuring of KrF Excimer laser-irradiated Aluminum (Al) has been correlated with laser-produced structural and mechanical changes. The effect of non-reactive Argon (Ar) and reactive Oxygen (O2) environments on the surface, structural and mechanical characteristics of nano-second pulsed laser-ablated Aluminum (Al) has been revealed. KrF Excimer laser with pulse duration 20 ns, central wavelength of 248 nm and repetition rate of was utilized for this purpose. Exposure of targets has been carried out for 0.86, 1, 1.13 and 1.27 J·cm−2 laser fluences in non-reactive (Ar) and reactive (O2) ambient environments at a pressure of 100 torr. A variety of characteristics of the irradiated targets like the morphology of the surface, chemical composition, crystallinity and nano hardness were investigated by using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Energy Dispersive X-ray Spectroscopy (EDS), X-ray Diffractometer (XRD), Raman spectroscopy and Nanohardness tester techniques, respectively. The nature (reactive or non-reactive) and pressure of gas played an important role in modification of materials. In this study, a strong correlation is observed between the surface structuring, chemical composition, residual stress variation and the variation in hardness of Al surface after ablation in both ambient (Ar, O2). In the case of reactive environment (O2), the interplay among the deposition of laser energy and species of plasma of ambient gas enhances chemical reactivity, which causes the formation of oxides of aluminum (AlO, Al2O3) with high mechanical strength. That makes it useful in the field of process and aerospace industry as well as in surface engineering.