Ali Al-Shaikhi

Ms. Ali Al-Shaikhi

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2022 in Energies
Verified
Journal Article
Open access
PDF file
Shafiqur RehmanShafiqur Rehman
Shafiqur Rehman
MMMohamed Mohandes
Mohamed Mohandes
AHAlaa El-Din Hussein
Alaa El-Din Hussein
LAL. M. Alhems
L. M. Alhems
AAAli Al-Shaikhi
Ali Al-Shaikhi
This study demonstrates that a drone flying above photovoltaic (PV) panels can clean the dust and enhance the panels’ efficiency. If operated regularly, the drone’s downward thrust generated during its cruise at a certain height above the panels can remove most of the accumulated dust. Sandstorms are frequent in Saudi Arabia, creating dust deposition on PV panels, which acts as a shield against solar radiation. As a result, the energy absorption from solar radiation is reduced and subsequently, the panels’ energy output is reduced. This experimental investigation was conducted at KFUPM University’s beach, Dhahran, Saudi Arabia, to prove the effectiveness of drone-based cleaning of PV panels. Volumes of 20, 50, and 100 CC of dust were spread on the panel during different experiments. These experimental results showed that the back thrust of the drone could remove most of the dust and improve the solar panels’ energy output performance. For example, for 50 CC dust spread on the panel, the current increased from 1.34 A to 2.16 A (61.2% increase), relative to the pre- and post-drone flight for horizontal movement of the drone. Similarly, for vertical and diagonal movements, the current increased by 69.83% and 68.03%, respectively, for a dust spread of 20 CC. Furthermore, dust reductions of 74.64%, 57.0%, and 78.4% were realized during the horizontal, vertical, and diagonal paths, respectively, of the drone flight for 50 CC dust spread.

12 June 2018 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
AAAli Al-Shaikhi
Ali Al-Shaikhi
AKAdil H. Khan
Adil H. Khan
AAAli T. Al-Awami
Ali T. Al-Awami
AZAzzedine Zerguine
Azzedine Zerguine

9 January 2017 in IEEE Wireless Communications Letters
Verified
Journal Article
Closed access
AAAli Al-Shaikhi
Ali Al-Shaikhi
AMAhmad Masoud
Ahmad Masoud
This letter develops a single-hop fast accurate and energy-efficient time synchronization protocol for wireless sensor networks. The protocol is designed to operate in harsh environments and is based on a resistive electrical network metaphor. It treats the nodes' times as the states of a discrete decentralized unconditionally stable dynamical system. The synchronizer monitors the evolution of these states during the transient phase to determine the instant at which the time encoded by a state is close to the master node time. The procedure can yield high quality time estimates with accuracies that are fractions of the communication cycle. The synchronization method is developed and its capabilities are demonstrated by simulation and physical experiments on the MICA-Z wireless sensor network.

1 January 2022 in FME Transactions
Verified
Journal Article
Open access
PDF file
HNH. Nuha
H. Nuha
MMM. Mohandes
M. Mohandes
SRS. Rehman
S. Rehman
AAAli Al-Shaikhi
Ali Al-Shaikhi
The cost of measuring wind speed (WS) increases significantly with mast heights. Therefore, it is required to have a method to estimate WS at hub height without the need to use measuring masts. This paper examines using the Regularized Extreme Learning Machine (RELM) to extrapolate WS at higher altitudes based on measurements at lower heights. The RELM uses measured WS at heights 10-40 m to estimate WS at 50 m. The estimation results of 50 m are further used along with the measured WS at 10-40 to estimate WS at 60 m. This procedure continues until the estimation of 180 m. The RELM's performance is compared with the regression tree (RegTree) method and the standard 1/7 Power Law. The proposed algorithm provides an economical method to find wind speed at hub height and, consequently, the potential wind energy that can be generated from turbines installed at hub height based on measurements taken at much lower heights. Moreover, these methods' extrapolated values are compared with the actual measured values using the LiDAR system. The mean absolute percentage error (MAPE) between extrapolated and measured WS at the height of 180 m using measurements at the height of 10-40 m using RELM, RegTree, 1/7 Power Law, and Power Law with adaptive coefficients is 13.36%, 16.76%, 33.50%, and 15.73%, respectively.

26 December 2019 in IEEE Access
Verified
Journal Article
Open access
AMAhmad A. Masoud
Ahmad A. Masoud
MAMohammad Abu-Ali
Mohammad Abu-Ali
AAAli Al-Shaikhi
Ali Al-Shaikhi
State space systems and experimental system identification are essential components of control education. Early introduction of these tools to the curriculum of a control laboratory in an interconnected and accessible manner that does not over-dilute the concepts is important in two ways. First, it facilitates a student’s transition to more senior and graduate level control concepts. It also provides an effective link to industrial applications. This paper provides two novel experimental procedures for directly identifying the state space model of a DC motor in an undergraduate control laboratory. The procedures do not require any specialized hardware and can be performed using standard laboratory equipment. They also do not place any simplifying assumptions on the motor’s model. The first procedure is based on direct pseudo inversion of the state space model. It does not require advanced knowledge of the state space approach or signal filtering. It is easy to understand and suits a first control laboratory. The second procedure is more efficient. It is based on the Markov approach commonly used for realizing, indirectly, a state space model from an estimated transfer function. While the procedure is designed for use by undergraduate students, it requires relatively advanced knowledge in state space that makes it suitable for a second undergraduate control laboratory.

30 October 2023 in IEEE Transactions on Vehicular Technology
Verified
Journal Article
Closed access
Mohammed ElamassieMohammed Elamassie
Mohammed Elamassie
AAAli Al-Shaikhi
Ali Al-Shaikhi
Sadiq SaitSadiq Sait
Sadiq Sait
MUMurat Uysal
Murat Uysal
Due to its high capacity and the ability to operate in an unregulated spectrum, free space optical (FSO) communication is ideally suited for airborne backhauling. In this paper, we consider a relay-assisted airborne FSO system in which serial and parallel relaying are deployed together. We deploy relay selection in each hop and select the relay that provides the maximum instantaneous signal-to-noise ratio (SNR). To achieve this in practice, it is necessary to estimate the channel coefficient per hop and feed it back to the preceding transmitting/relaying node. Due to the semi-fixed hovering position of rotary-wing unmanned aerial vehicles (UAVs), this estimate will likely be outdated for the airborne channel. Therefore, the relay will likely be selected based on the outdated channel coefficient. In this paper, we first propose a model for outdated log-normal fading. Based on the outdated channel state information, we discuss how to optimally set the node transmit power by a proper selection of the pre-amplification factor to ensure signal reception above a targeted threshold at each hop. We finally present the end-to-end bit error rate (BER) performance of the airborne parallel multi-hop system under consideration.