Asphaltene precipitation/deposition is considered a problem of formation damage, which can reduce the oil recovery factor. In addition, asphaltenes can be deposited in pipelines and surface installations, causing serious complications in guaranteeing runoff, decreasing the production of oil wells. The precipitation of asphaltenes can be minimized by reducing the oil production flowrate or by using chemical inhibitors. Analyzing the stability and precipitation trend of asphaltenes in petroleum is vital for the guarantee of flow. For this purpose, several experimental and numerical methods have been proposed. Once the risk of precipitation is established, strategies can be formulated for the prevention and diagnosis of deposition problems in production or production training. The tests can be performed with dead oil, available in the wellhead, and help in understanding the behavior of the asphaltenes. This review aims to present (i) the problem related to the precipitation of asphaltenes; (ii) thermodynamic models of asphaltene precipitation; and (iii) asphaltene inhibition, control, and removal techniques using nanoparticles.

Several solutions have been presented to minimize the environmental impact generated by polymers produced from petroleum resources. This work produced a biopolymer using glycerol, starch (<5) and macaúba epicarp fiber (10–15–20–25–30%) as reinforcement. The interaction of glycerol with starch was favored by the addition of acetic acid (CH₃COOH). The pH was adjusted with sodium hydroxide (NaOH) at a concentration of 0.1 mol·L⁻¹. The characterization was carried out through scanning electron microscopy (SEM), infrared reflectance—FTIR, water solubility, biodegradability and technological properties. Through the results obtained in this work, it is observed that the tensile strength and modulus of elasticity are influenced by the addition of the fiber concentration; the sample that received a 30% addition presented 19.17 MPa and 348.12 MPa, respectively. All samples showed low solubility in water and low density, in addition to a high rate of degradability in soil with mass loss corresponding to 59% over a period of three months. The results of this investigation are satisfactory for the production of materials that can be used in everyday life, replacing conventional plastic.

Closed pore glass foams with dimensions of 60mm × 20 mm × 20 mm were produced using agro-industrial residues. Samples containing sodo-calcic glass powder (78%wt) and rice husk ash (16%wt) were characterized, and their technological properties were investigated. The samples were synthesized in a conventional muffle furnace at 750–800–850 °C. The results presented for apparent density (0.24–0.29 g/cm³), compressive strength (1.5–2.3 MPa) and thermal conductivity (0.021–0.025 W/mK) meet the standards for commercial foam glasses. Low viscosity was achieved at all temperatures as a result of the addition of rice husk ash to the cell structure. X-ray fluorescence showed that the glass was silico-sodo-calcic type (SiO₂, Na₂O and CaO), and that the rice husk ash was rich in SiO₂ (as well as CaO, Na₂O, Al₂O₃, K₂O and Fe₂O₃). The mechanical strength and low thermal conduction of the material showed a good efficiency for use in civil construction as a thermal insulating material. Material made in this way has a lower production cost, and additionally transforms waste into co-products, generating added value, favoring consecutive circulation, as well as a clean and circular economy.

During petroleum industry operations, burning flammable gas components in the flaring stacks is common, normally a symbol for stable production, but flaring these components creates harmful emissions for the environment. This flaring gas has components with a high quantity of heating power, an important measurement that quantifies the energy that can potentially be obtained from this wasted resource. This paper aims to evaluate the energy usage of the flaring gas, estimating the possible energy produced with this usable resource by modeling a treatment and energy generation process employing the Aspen HYSYS^® simulator. The flaring gas is characterized using different models and compositional ranges of natural gas to know what kind of gas it is and identify what type of equipment could be used for treatment and energy generation from this resource. After the gas characterization, the selection of the equipment of treatment and energy generation is necessary; this is done using a multicriteria analysis by taking into consideration the variables of gas composition, electrical efficiency, economic performance, and GHG emissions, ensuring to generate the greatest amount of energy possible to be produced with this flaring gas. By increasing the LHV, 0.95 MMSCF of flared gas of an oilfield in the VMM basin produced 5133 kW, enough energy to supply gas treatment and power generation facilities and four times the total gross consumption energy of a model oilfield in the basin, while the CO₂ emissions were reduced 11.4%, and cost savings using this resource instead of diesel were obtained. In conclusion, to minimize flaring and to recover and reuse these waste components, looking for alternatives for the use of this gas-like power generation is an important option that reduces pollutants emission, gives a new source of fuel, and gives an energy usefulness to this wasted resource.