The primary objective of this study is to develop a novel experimental nanofluid based on surfactant–nanoparticle–brine tuning, subsequently evaluate its performance in the laboratory under reservoir conditions, then upscale the design for a field trial of the nanotechnology-enhanced surfactant injection process. Two different mixtures of commercial anionic surfactants (SA and SB) were characterized by their critical micelle concentration (CMC), density, and Fourier transform infrared (FTIR) spectra. Two types of commercial nanoparticles (CNA and CNB) were utilized, and they were characterized by S_BET, FTIR spectra, hydrodynamic mean sizes (dp₅₀), isoelectric points (pH_IEP), and functional groups. The evaluation of both surfactant–nanoparticle systems demonstrated that the best performance was obtained with a total dissolved solid (TDS) of 0.75% with the SA surfactant and the CNA nanoparticles. A nanofluid formulation with 100 mg·L⁻¹ of CNA provided suitable interfacial tension (IFT) values between 0.18 and 0.15 mN·m⁻¹ for a surfactant dosage range of 750–1000 mg·L⁻¹. Results obtained from adsorption tests indicated that the surfactant adsorption on the rock would be reduced by at least 40% under static and dynamic conditions due to nanoparticle addition. Moreover, during core flooding tests, it was observed that the recovery factor was increased by 22% for the nanofluid usage in contrast with a 17% increase with only the use of the surfactant. These results are related to the estimated capillary number of 3 × 10⁻⁵, 3 × 10⁻⁴, and 5 × 10⁻⁴ for the brine, the surfactant, and the nanofluid, respectively, as well as to the reduction in the surfactant adsorption on the rock which enhances the efficiency of the process. The field trial application was performed with the same nanofluid formulation in the two different injection patterns of a Colombian oil field and represented the first application worldwide of nanoparticles/nanofluids in enhanced oil recovery (EOR) processes. The cumulative incremental oil production was nearly 30,035 Bbls for both injection patterns by May 19, 2020. The decline rate was estimated through an exponential model to be −0.104 month⁻¹ before the intervention, to −0.016 month⁻¹ after the nanofluid injection. The pilot was designed based on a production increment of 3.5%, which was successfully surpassed with this field test with an increment of 27.3%. This application is the first, worldwide, to demonstrate surfactant flooding assisted by nanotechnology in a chemical enhanced oil recovery (CEOR) process in a low interfacial tension region.

Asphaltene precipitation/deposition is considered a problem of formation damage, which can reduce the oil recovery factor. In addition, asphaltenes can be deposited in pipelines and surface installations, causing serious complications in guaranteeing runoff, decreasing the production of oil wells. The precipitation of asphaltenes can be minimized by reducing the oil production flowrate or by using chemical inhibitors. Analyzing the stability and precipitation trend of asphaltenes in petroleum is vital for the guarantee of flow. For this purpose, several experimental and numerical methods have been proposed. Once the risk of precipitation is established, strategies can be formulated for the prevention and diagnosis of deposition problems in production or production training. The tests can be performed with dead oil, available in the wellhead, and help in understanding the behavior of the asphaltenes. This review aims to present (i) the problem related to the precipitation of asphaltenes; (ii) thermodynamic models of asphaltene precipitation; and (iii) asphaltene inhibition, control, and removal techniques using nanoparticles.

The primary objective of this study is the development of nanofluids based on different diluent/dispersant ratios (DDR) for extra-heavy oil (EHO) viscosity reduction and its perdurability over time. Different diluents such as xylene, diesel, n-pentane, and n-heptane were evaluated for the formulation of the carrier fluid. Instability of asphaltenes was assessed for all diluents through colloidal instability index (CII) and Oliensis tests. Rheology measurements and hysteresis loop tests were performed using a rotational rheometer at 30 °C. The CII values for the alkanes type diluents were around 0.57, results that were corroborated with the Oliensis tests as asphaltenes precipitation was observed with the use of these diluents. This data was related to the viscosity reduction degree (VRD) reported for the different diluents. With the use of the alkanes, the VRD does not surpass the 60%, while with the use of xylene a VRD of approximately 85% was achieved. Dimethylformamide was used as a dispersant of the nanoparticles and had a similar VRD than that for xylene (87%). Subsequent experiments were performed varying the DDR (xylene/dimethylformamide) for different dosages up to 7 vol % determining that a DDR = 0.2 and a dosage of 5 vol % was appropriated for enhancing EHO VRD, obtaining a final value of 89%. Different SiO₂ nanoparticles were evaluated in the viscosity reduction tests reporting the best results using 9 nm nanoparticles that were then included at 1000 mg·L⁻¹ in the carrier fluid, increasing the VRD up to 4% and enhancing the perdurability based on the rheological hysteresis and the viscosity measurements for 30 days. Results showed a viscosity increase of 20 and 80% for the crude oil with the nanofluid and the carrier fluid after 30 days, respectively. The nanoparticles have a synergistic effect in the viscosity reduction and the inhibition of the viscoelastic network re-organization (perdurability) after treatment application which was also observed in the rheological modeling carried out with Cross and Carreau models as the reported characteristic relaxation time was increased almost a 20%. Moreover, the Vipulanandan rheological model denotes a higher maximum stress value reached by the EHO with the addition of nanofluids which is derived from the EHO internal structure rearrangement caused by the asphaltenes adsorption phenomenon.

The objective of this study is to reduce heavy oil viscosity through the catalytic decomposition of heavy fractions by ultrasound cavitation using metal oxide nanoparticles and water as a hydrogen donor, leading to the reduction of asphaltene content through its conversion into lighter components. NiO nanoparticles were synthesized over a 7 nm silica support using the incipient wetness technique. Emulsified heavy oil (HO) with 40%v/v of water and 13°API was used to evaluate the ultrasound cavitation process over different exposure times and nanoparticle dosages. The viscosity of the emulsified HO before and after ultrasound cavitation was measured with and without nanoparticles. Significant viscosity reduction was obtained, showing best results at 90 minutes of ultrasound exposure time with a nanoparticle dosage of 2000 mg/L, leading to a viscosity reduction at 10 s-1 and 25°C, and an asphaltene content reduction of 44 and 16%, respectively.