The thermal performance of a phase change energy storage building envelope with the ventilated cavity was evaluated. CaCl2·6H2O-Mg(NO3)2·6H2O/expanded graphite (EG) was employed to combined with the building for year-round management. The energy consumption caused by the building under different influence parameters was evaluated numerically. The results indicated that CaCl2·6H2O-8wt %Mg(NO3)2·6H2O/EG should be installed on the south wall for the heating season, while CaCl2·6H2O-2wt %Mg(NO3)2·6H2O/EG should be integrated on the roof for the cooling season. When the air layer was ventilated and the south wall was coated with the solar absorbing coating, the room could save approximately 30% of energy consumption. Moreover, the energy consumption increased with an increase in the air layer thickness, and the air layers played a different role in the building envelope. The optimal value of the flow rate between air layer 2, air layer 3, and the room was 0.09 m3/s. To reduce the energy consumption, the phase change materials (PCMs) with large and small thermal conductivity should be installed in the south wall and roof, respectively. In general, the phase change energy storage building envelope with the ventilated cavity can save energy during the heating and cooling seasons.
In this paper, a series of eutectic hydrated salts was obtained by mixing Na2HPO4·12H2O (DHPD) with K2HPO4·3H2O (DHPT) in different proportions. With the increase in the content of DHPT, the phase transition temperature and melting enthalpy of eutectic hydrated salts decreased gradually. Moreover, the addition of appropriate deionized water improved the thermal properties of eutectic hydrated salts. Colloidal silicon dioxide (SiO2) was selected as the support carrier to adsorb eutectic hydrated salts, and the maximum content of eutectic hydrated salts in composite PCMs was 70%. When the content of the nucleating agent (Na2SiO3·9H2O) was 5%, the supercooling degree of composite PCMs was reduced to the minimum of 1.2 °C. The SEM and FT-IR test results showed that SiO2 and eutectic hydrated salts were successfully combined, and no new substances were formed. When the content of DHPT was 3%, the phase transition temperature and melting enthalpy of composite PCMs were 26.5 °C and 145.3 J/g, respectively. The results of thermogravimetric analysis and heating–cooling cycling test proved that composite PCMs had good thermal reliability and stability. The application performance of composite PCMs in prefabricated temporary houses was investigated numerically. The results indicated that PCM panels greatly increased the Grade I thermal comfort hours and reduced energy consumption. Overall, the composite PCM has great development potential building energy conservation.
1 January 2024 in International Journal of Energy Research
In this work, it was first proposed to combine hydrated salt phase change materials (PCMs) with humidity control materials to prepare the temperature and humidity control material. The composite PCM was prepared by absorbing Na2HPO4·12H2O with colloidal silicon dioxide, and diatomite was selected as the humidity control material. The humidity performance tests found that diatomite had good moisture absorption/desorption capacity and excellent moisture buffering capacity. The supercooling degree tests showed that Na2SiO3·9H2O as nucleating agent effectively reduced the supercooling degree, and the addition of deionized water improved the water loss problem of composite PCMs. The DSC tests showed that the enthalpy and melting temperature of composite PCMs were 153.1 J/g and 28.9°C, respectively. By placing the temperature and humidity control material in different humidity, it was found that the moisture content of diatomite affected the thermal properties of composite PCMs. Diatomite could not only transfer moisture to hydrated salts but also absorb moisture from hydrated salt. The application performance tests of the temperature and humidity control material in the room model showed that it could simultaneously regulate indoor temperature and humidity. Overall, this temperature and humidity control material was more suitable for environments with high relative humidity such as greenhouses.
24 October 2025 in Journal of Thermal Analysis and Calorimetry