Rabelani Dennis Murwamadala

Mr. Rabelani Dennis Murwamadala

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 March 2023 in Advances in Materials and Processing Technologies
Verified
Journal Article
Open access
RMRabelani Dennis Murwamadala
Rabelani Dennis Murwamadala
VRVasudeva Veeredhi Rao
Vasudeva Veeredhi Rao
This study studied the tribological properties of PVD AISI 4140 low – alloy TiN coated and reported. The morphologies before testing are assessed with a laser confocal microscope and XRD. Three tests are conducted per sample: the rotating, scratch, and reciprocation tests. The contour of counter bodies and wear scares are studied and reported. The wear scares are also further studied using the SEM-EDS chemical analysis to study the amount of wear that has occurred. The results showed a change in roughness and waviness after coating. In the reciprocating tests showed a high degree of spalling on the TiN sample is observed with a higher wear volume compared to the substrate. However, a lower coefficient of friction is observed. This is similar to the rest of the tests.

1 May 2026 in Engineering Research Express
Verified
Journal Article
Open access
RMRabelani Dennis Murwamadala
Rabelani Dennis Murwamadala
Polylactic acid (PLA) filaments are favored in additive manufacturing because of their affordability and recyclability. However, pure PLA polymers exhibit limited tribological properties. To address this limitation, filaments have recently been enhanced with reinforcements or fillers. In this study, a parametric analysis was conducted to assess the influence of printing speed, layer height, and nozzle temperature on the tribological performance of 3D-printed carbon-PLA. Surface evaluations were performed using a laser confocal microscope, and the data were analyzed using Mountains 9.0 software to determine the functional surface parameters. The results indicate that the printing parameters directly affect these functional surface parameters. For S ku , the highest and lowest values were 97.06 and 58.26 for samples 1 and 16, respectively, while for the same samples, S sk was −8 and −16, respectively. The areal surface roughness parameters, S q and Sa , were ∼14 and 11 µ m for sample 12. The same sample had the highest S vk at 3624 µ m and S k at 14,92 µ m; however, S pk was the lowest at 3875 µ m. Similarly, the surface volume parameters V vc and V vv were 0.008 492 and 0.003 33 mm 3 mm −2 , respectively. Tribological wear tests were conducted at room temperature using the dry pin-on-disc method. The wear rate and coefficient of friction (COF) were investigated, and the wear mechanisms were inferred from scanning electron microscopy images of wear tracks. The wear tracks displayed plowing, entrapped debris, and wedge formation, and the COF ranged from approximately 0.15–0.35. The wear rate ranged from 0.0001 to 0.0024 mm 3 mm −2 . Gray relational analysis was used to determine the optimal parameter values. Analysis of variance revealed that layer height had the greatest influence on the COF, whereas the nozzle temperature most significantly affected the wear rate. The optimal printing parameters were identified as 40 mm s −1 printing speed, 0.25 mm layer height, and 200 °C nozzle temperature.

5 August 2026 in Materials Research Express
Verified
Journal Article
Open access
PDF file
RMRabelani Dennis Murwamadala
Rabelani Dennis Murwamadala
LLLebogang Lebea
Lebogang Lebea
Lekhetho Ambition RamosenaLekhetho Ambition Ramosena
Lekhetho Ambition Ramosena
The mechanical properties of components manufactured via fused filament fabrication (FFF) are significantly influenced by defects that occur during printing and post-processing conditions. This study thoroughly investigated the effects of post-heat treatment on the internal microstructure and mechanical properties of 3D-printed polylactic acid (PLA) reinforced with short carbon fibers (PLA–CF). Samples were produced using FFF and subsequently annealed at 50 and 120 °C for 2 h. X-ray microscopy (XRM) was employed to assess the internal defects, void distribution, and microstructural changes at both the macro and micro levels resulting from the heat treatment. XRM volume segmentation revealed that voids decreased steadily as the treatment temperature increased. The untreated samples had a solid-to-void ratio of 56.205%. The sample treated at 50 °C had a ratio of 56.72%, and the sample treated at 120 °C had a solid-to-void ratio of 58.922%. Mechanical testing adhered to ASTM D638 standards, and the experimentally determined geometries were used in finite element analysis models to confirm the thermomechanical responses. The findings revealed that annealing improved the tensile strength and ductility by enhancing interlayer bonding and reducing porosity while preserving material toughness. These results highlight the significance of controlled heat treatment in optimizing the performance of FFF-printed PLA–CF composites and demonstrate the value of incorporating XRM-informed geometries into computational models for accurate-performance prediction.