Lebogang Lebea

Dr. Lebogang Lebea

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 November 2021 in International Journal of Mechanical and Materials Engineering
Verified
Journal Article
Open access
PDF file
LLLebogang Lebea
Lebogang Lebea
HNH. M. Ngwangwa
H. M. Ngwangwa
DDD. Desai
D. Desai
FNF. Nemavhola
F. Nemavhola
The initial stability after implantology is paramount to the survival of the dental implant, and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of three-dimensional printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of three-dimensional printed dental implants and three-dimensional printed dogbone tensile samples under areal height parameters, amplitude parameters (average of ordinates), skewness parameters and mechanical properties. During the experiment, roughness values were analysed, and the results showed that the skewness parameter demonstrated a minimum value of 0.59%. The three-dimensional printed dental implant recorded the arithmetic mean deviation of the assessed profile with a 3.4-mm diameter at 43.23% and the three-dimensional printed dental implant with a 4.3-mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress decreases from 968.35 to 955.25 MPa, the arithmetic mean deviation increases by 1.4%, and when ultimate tensile stress increases to 961.18 MPa, the arithmetic mean deviation increases by 0.6%. When the cycle decreases from 262,142 to 137,433, the arithmetic mean deviation shows that less than a 90.74% increase in the cycle is obtained. For the three-dimensional printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

16 April 2022 in Applied Bionics and Biomechanics
Verified
Journal Article
Open access
PDF file
LLLebogang Lebea
Lebogang Lebea
Harry M NgwangwaHarry M Ngwangwa
Harry M Ngwangwa
Dawood DesaiDawood Desai
Dawood Desai
Fulufhelo NemavholaFulufhelo Nemavhola
Fulufhelo Nemavhola
Corrosion in the human body can cause materials to change structurally and release undesirable products that may bring about complications such as toxicity and inflammation. These may jeopardize the mechanical stability of prostheses. The purpose of this study was to evaluate the effect of solutions (Ringer’s and table salt [NaCl]) and immersion periods on 3D-printed titanium alloy Ti64-ELI samples and the changes in mechanical properties before and after corrosion testing. The microstructure of prepared samples was analyzed, and the formation of α- and β-phases was studied. During testing, the β-phases showed up as white, and the α-phases presented as dark. In both, corrosion by pitting was observed after corrosion analysis. The results show that, by comparing NaCl and Ringer’s, the of the solutions increased by 0.8 V and the decreased by an order of magnitude. It was observed that the weight loss in the solutions will lead to dental implant instability and will cause failure.

27 September 2022 in Material Design & Processing Communications
Verified
Journal Article
Open access
PDF file
MPMOTHIBELI PITA
MOTHIBELI PITA
LLLebogang Lebea
Lebogang Lebea
Mild steel is a common material used extensively in the manufacturing industry. This manuscript investigates the effect of cooling processes on the hardness, toughness, coefficient of friction, and wear rate of mild steel heat treated at different temperatures. The material was heat treated in a furnace at two different temperatures (500 and 900°C) and cooled by water, oil, and air. Microhardness and impact tests were conducted using ASTM E384 and ASTM E23-12C. For dry conditions, the tribology ASTM G99 test standard was used to determine the coefficient of friction and wear rate per sample. The results show that mild steel heat treated at 900°C and cooled with water increased the material’s hardness by 24% and toughness by 23.3% as compared to oil- and air-cooling media. The same heating temperature and water-cooling media produce the material with a low wear rate (3.223E-008).

26 October 2021 in Research Square
Verified
Preprint
Open access
PDF file
LLLebogang Lebea
Lebogang Lebea
Harry M NgwangwaHarry M Ngwangwa
Harry M Ngwangwa
TPThanyani Pandelani
Thanyani Pandelani
Fulufhelo NemavholaFulufhelo Nemavhola
Fulufhelo Nemavhola
The function of the omasum is incompletely understood; however, the omasum plays an important role in the transport of appropriately sized feed particles from the reticulorumen to the abomasum, oesophageal groove closure, fermentation of ingesta, and absorption of water, volatile fatty acids, and minerals. The aim of this study is to evaluate the suitable hyperelastic anisotropic model based on biomechanical properties of sheep omasum. The results show that all five (5) hyperelastic models may be suitable for the evaluation of sheep omasum. The average coefficient of determination (R2) of Fung, Polynomial (Anisotropic), Holzapfel (2000), Holzapfel (2005) and Four-Fiber-Family hyperelastic models were found to be 0.79 ± 0.19, 0.95 ± 0.05, 0.92 ± 0.07, 0.93 ± 0.05 and 0.94 ± 0.03, respectively. Also, it was found that the best hyperelastic model for fitting uniaxial data of the sheep omasum was Polynomial (Anisotropic) with EI of 100.0 followed by the Four-Fiber-Family model with EI of 96.18.

1 January 2023
Verified
Book Chapter
Closed access
PDF file
LLLebogang Lebea
Lebogang Lebea
HNH. M. Ngwangwa
H. M. Ngwangwa
ASAnand Kumar Subramaniyan
Anand Kumar Subramaniyan

15 November 2024 in Frontiers in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
LLLebogang Lebea
Lebogang Lebea
DDDawood Desai
Dawood Desai
HNHarry Ngwangwa
Harry Ngwangwa
FNFulufhelo Nemavhola
Fulufhelo Nemavhola
Titanium alloy Ti6Al4V is extensively utilized in biomedical applications due to its excellent biocompatibility, corrosion resistance, and mechanical properties. The design of dental implant surface textures has changed throughout time to address issues with oral rehabilitation in both healthy and damaged bones. The longevity of an implant is significantly impacted by surface roughness. This study examines the use of laser shock peening (LSP) as a surface modification technique to improve the mechanical properties of implants. A numerical model is developed using the commercial finite elements software in ABAQUS/Explicit for simulating dynamic conditions. The aim of the study is to develop surface roughness parameters using computational methods such as studies have not yet been contemplated. The single shot angle, shot repeat, time, material orientation, and laser power are applied for the first time simultaneously to evaluate the impact of material orientation and loading angles on surface roughness parameters. The study showed that the developed computational model’s compressive residual stress was −578.45 MPa, while the experimental samples were −592.18 MPa. Consequently, the difference between the computational and experimental results was 2.32%. Without regard to material orientation or angle, the compressive residual stress of the samples under examination was found to be −578.450 MPa after three repetitions and to decreased to −1.620 MPa after four. These results demonstrate that by varying the material orientation and loading angle, the Ra value may be increased four times.