The aim of this paper is to present a chemical composition and quantities of mining and processing waste landfills material developed during historical mining and smelting. After detailed inspection, it was found that approximately 2.6 gigatons of the waste had been deposited at 1650 sites, covering almost 65 km². More than half of this material, 55%, is characterized as conventional mining waste, 37% belongs to the processing tailings, and 8% to metallurgical waste. Most of these tailing sites are unclaimed, presenting a source of contamination for nearby communities. According to the literature data collected and additional chemical analyses, in accordance with zero-waste philosophy, about 42 promising locations (c. 270 million tons) could be selected, where various advanced eco-innovative methods of recovery could possibly apply. The areas with the highest prospective recovery are Serbia and Kosovo. In accordance with the metal prices achieved in March 2022, it is estimated that the recovery of tailings could bring up to 18,100 million USD, which is much more compared to the prices of March 2020—10,600 million USD—when the commodity market was governed by the COVID-19 restrictions. In addition to the commercial value of the metals, the environmental aspect should not be forgotten after the application of reuse and recycling concepts.

Flotation wastes are becoming a valuable secondary raw material and source of many metals and semimetals worldwide with the possibilities of industrial recycling. The flotation tailings contain oxide and sulfide minerals that have not been sufficiently stabilized and form acidic mine waters, which in turn contaminate groundwater, rivers, and reservoi6sediments. An effective way to recycle these mine wastes is to recover the metals through leaching. While the focus is on acid bioleaching by iron- and sulfur-oxidizing bacteria, alkaline leaching, and the removal of iron-containing surface coatings on sulfide minerals contribute significantly to the overall environmental efficiency of leaching. For this study, static and percolate bioleaching of copper from flotation waste at the Bor copper mine in Serbia was investigated in alkaline and then acidic environments. The aim of the study was to verify the effect of alkaline pH and nutrient stimulation on the bioleaching process and element extraction. A sample was taken from a mine waste site, which was characterized by XRF analyses. The concentration of leached copper was increased when copper oxide minerals dissolved during alkaline bioleaching. The highest copper yield during alkaline bioleaching was achieved after 9 days and reached 67%. The addition of nutrients in acidic medium enhanced the degradation of sulfide minerals and increased Cu recovery to 74%, while Fe and Ag recoveries were not significantly affected. Combined bioleaching with alkaline media and iron- and sulfur-oxidizing bacteria in acidic media should be a good reference for ecological Cu recovery from copper oxide and sulfide wastes.

The technological process of exploitation of mineral resources and processing of mined ores to cater to the market results, among other things, in a large amount of tailings deposed on tailing ponds. Because of the chemical composition of the material, the increasing amount of waste, and the mismanagement of recovery and reclamation of ponds, these ponds have become a significant element of negative impact on the surrounding ecosystem. Economics was behind the discharging of this material, resulting in tailing ponds created in inappropriate areas. There is an ongoing process of depositing tailings on old tailing ponds, although no special attention has been paid to the subsequent effect on the environment. Application of intelligent multi-criteria analysis AHP and PROMETHEE has been performed in this paper for the purpose of ranking the degree of negative impact on the environment of tailing ponds. Analysis is performed for five tailing ponds of MMCC (Mining Metallurgy Chemical Combine) “Trepča”, whereby two of the ponds are active and three inactive. The ponds are in relatively close proximity to the municipalities of Zvečan and Kosovska Mitrovica, to the north of Kosovo and Metohija, Republic of Serbia. In order to achieve the most objective results, the AHP and PROMETHEE methods were applied. By using these methods for calculations, the following ranking for the flotation tailing waste deposits was obtained, regarding their environmental impact: Žitkovac, Tvrđanski Do, Bostanište, Gornje Polje and Žarkov Potok. This result can contribute to the decision-making process of a prioritizing strategy for rehabilitation and remediation of these five flotation tailings. The analysis illustrates that application of intelligent multi-criteria analysis is a useful environmental management tool to be included in the decision-making process.

As the mine planning is one of the most complicated steps, which depends on a lot of factors as geology, economy etc., consequently, the decision-making process is difficult, due to the existence of a lot of factors for choosing the optimal mining system. In this paper, the method and the result...

In a continuous system of production in open-cast coal mining, in addition to the basic machinery which consists of highly productive machines (bucket-wheel excavators, bucket-chain excavators, spreaders, conveyor-belt transporters, etc.) that provide an uninterrupted exploitation of mineral ores, the usage of auxiliary machinery is also necessary. The auxiliary machinery provides the possibility of using the capacities of basic machinery adequately and timely. Further, it must be mentioned that the auxiliary machinery generates up to 20% of the total mining expenses. Dozers are the most commonly used machines. Choosing the adequate dozer of the right type and manufacturer is of great importance and can be made easier by carrying out an analysis of the existent operational-exploitative parameters. In this paper, the method of grading the operational-exploitative parameters of dozer is defined. The choice of the optimal type of dozer was conducted by using the analytical hierarchy process (AHP).

In the presented paper, activated carbons were prepared from fructose and glucose, and activating agents (KOH, NaOH, LiOH) by hydrothermal treatment (HTC) treatment. After preparation, samples were characterized in details. Different techniques were used: x-ray powder diffraction analysis, Raman spectral analysis, elemental analysis, and determination of textural and morphological properties. Obtained results showed dependence of investigated properties and the nature of precursors (glucose or fructose) as well as the type of hydroxides used as activating agents. After characterization, samples were tested as materials for heavy metals (Pb²⁺, Cd²⁺ and Zn²⁺) and methylene blue removal. Also, adsorption experiments were performed on wastewaters taken from tailings of the lead and zinc mine and kinetic of the methylene blue removal was studied. The factors which distinguished the KOH activated samples were high yield (~14%), content of organic carbon (63–74%), porosity and specific surface area (S_BET ~700–1360 m²/g), a low degree of the crystal phase, indications that potassium ions may be included in heavy metals removal, good removal of the heavy metal ions (~47–59 mg/g for Pb²⁺, ~21–27 mg/g for Cd²⁺ and ~6–10 mg/g for Zn²⁺) and fast (~10–30 min) and good methylene blue (~60–200 mg/g) removal.