Previous studies indicate that traditional asphalt mixtures lack the ability to withstand the stresses caused by heavy traffic volumes under high temperatures. To enhance the rutting resistance of flexible pavement under high levels of temperature and loading, extensive laboratory experiments were carried out. A 60/70 grade bitumen was used as a neat sample for comparison. The study introduced three distinct polymers, polypropylene (PP), low-density polyethylene (LDPE), and acrylonitrile butadiene styrene (ABS), at varying concentrations by weight into the neat bitumen. Initially, conventional tests were performed to evaluate the conventional properties of both the neat and modified bitumen, while aggregate tests assessed the mechanical properties of the aggregates. Subsequently, a Marshall mix design was performed to determine the optimum bitumen content (OBC) in the asphalt mixture. Finally, wheel-tracking tests were performed under a specific load and temperature to investigate the rutting behavior of the modified asphalt mixtures. The results of this comprehensive study revealed that the modified asphalt mixtures displayed improved resistance to rutting compared to the neat asphalt mixture. Furthermore, it was also observed that the LDPE exhibited a superior performance against rutting, followed by the PP and ABS. At polymer contents of 3%, 5%, and 7%, the LDPE achieved reductions in rut depth of 13%, 24%, and 33%, respectively, outperforming both PP- and ABS-modified asphalt. These findings not only enhance our understanding of asphalt behavior under diverse conditions but also highlight the potential of plastic-modified asphalt as an effective solution for mitigating rutting problems in road pavements. By incorporating plastic modifiers into asphalt mixtures, this approach aligns with the principles of sustainable construction by reducing plastic waste while improving pavement durability and performance.

The amount of residual Multi-layer Plastic Packaging (MPP) in Canada has greatly increased in the last two decades, which has economic and environmental consequences. MPP is primarily made up of two or more layers of Polyethylene (PE), Polyester (PET), Nylon (NY), and Metalized Polyester (METPET). While MPP has not been used as an asphalt modifier, some of the materials commonly found in MPP, such as PE and PET, have also been successfully used as asphalt modifiers. Nevertheless, a few recent studies have demonstrated the potential for reusing MPP as an asphalt modifier to improve asphalt pavement performance. Recycling post-industrial MPP instead of using raw polymers could lead to economic and environmental benefits. However, a comprehensive study to evaluate MPP as a viable asphalt additive is lacking. The main objective of this study is to evaluate the feasibility of using MPP as an asphalt modifier via the wet method, considering the physical, thermal, rheological, and storage properties of the MPP-modified binder at different MPP concentrations (2%, 4%, and 8%) in asphalt cement (PG 58–28). MPP-modified binders were evaluated using the following instruments: Differential Scanning Calorimeter (DSC), Thermogravimetric Analysis (TGA), Superpave Dynamic Shear Rheometer (DSR), Rotational Viscosity (RV), and Environmental Scanning Electron Microscopy (ESEM). Test results indicated that the incorporation of MPP has a strong potential to improve permanent deformation resistance at high temperatures. In addition, MPP shows a moderate impact on fatigue cracking performance at intermediate temperatures. Overall, in low-temperature climates, using less than 4% of MPP additives would offer higher fatigue damage resistance along with adequate permanent deformation. In high-temperature climates, higher concentrations of additives may be preferable to resist permanent deformation. Finally, MPP is a challenge for existing recycling systems, and its incorporation into asphalt applications may develop more sustainable materials that would contribute to circular economy principles.

Thermal cracking significantly impacts the structural integrity of flexible pavements, particularly in colder regions like Canada. Limited studies investigated the impact of plastic modification of asphalt binders and mixtures using the wet method on the low-temperature performance of asphalt materials. The plastic material utilized in this project is multilayer plastic packaging (MPP). This study aims to determine whether MPP can be integrated to enhance the performance of the MPP-modified binder and MPP-modified mixtures, especially considering that MPP accounts for just over 40% of total plastic usage, making it the largest end-use market segment. This research evaluates the impact on rheological and mechanical behaviour when introducing MPP additives to conventional hot mix asphalt. This study used the wet method to test MPP-modified asphalt materials at 2%, 4%, and 8% (by weight of the asphalt binder). Test results demonstrate that the MPP modification percentage should ideally not exceed 2% as blends with 4% MPP or higher exhibited lower performance at low temperatures. The use of a softer binder as a base binder would help increase the MPP modification rates, but this hypothesis needs to be validated experimentally.

This study investigates the propagation of shear horizontal transverse waves in a functionally graded piezoelectric half-space (FGPHS), where the material properties vary linearly and quadratically. The analysis focuses on deriving and understanding the dispersion characteristics of such waves in in-homogeneous media. The WKB approximation method is employed to obtain the dispersion relation analytically, considering the smooth variation of material properties. To validate and study the wave behavior numerically, two advanced techniques were utilized: the Semi-Analytical Finite Element with Perfectly Matched Layer (SAFE-PML) and the Semi-Analytical Infinite Element (SAIFE) method incorporating a (1/r) decay model to simulate infinite media. The numerical implementation uses the Rayleigh–Ritz method to discretize the wave equation, and Gauss 3-point quadrature is applied for efficient numerical integration. The dispersion curves are plotted to illustrate the wave behavior in the graded piezoelectric medium. The results from SAFE-PML and SAIFE are in excellent agreement, indicating that these techniques effectively model the shear horizontal transverse wave propagation in such structures. This study also demonstrates that combining finite and infinite element approaches provides accurate and reliable simulation of wave phenomena in functionally graded piezoelectric materials, which has applications in sensors, actuators, and non-destructive testing.