In this study, drying kinetics, including thermal and moisture, of Codonopsis javanica with the support of ultrasonic technology in the drying process were investigated. Experimental processes were carried out at drying air temperatures of 40°C, 45°C, and 50°C with and without ultrasound at a frequency of 20 kHz and three levels of intensity: 1.3 kW/m2, 1.8 kW/m2, and 2.2 kW/m2. Based on theoretical calculations, experimental data, and the particle swarm optimization (PSO) algorithm, the coefficient of thermal diffusion was determined in the range of 1.01–1.36 × 10−7 m2/s, and the coefficient of moisture diffusion is in the range of 3.2–6.7 × 10−10 m2/s. In addition, the color parameters (,, and ) of the drying materials were also considered. Results showed the overall color differences (∆E) of dried products change in the range of 8.0–12.9 compared with the fresh ones. In this work, the multiple boundary conditions were considered to determine the moisture and thermal diffusion coefficients; the results obtained prove that the quality of dried products in terms of color change is also improved.
This study focused on the experimental drying of Bo Chinh ginseng by the ultrasound-assisted heat pump drying method, in which the effects of drying air temperature (T), ultrasonic power (P), intermittency ratio of ultrasound generator (A) on the moisture effective diffusion coefficient (Deff), saponin content (Sp) and color change (dE) during the drying process were determined. The results showed that the drying time was reduced from 12.5 h at 35 °C to 8.9 h at 40 °C and greatly reduced to 5.8 h at 55 °C. The moisture diffusion coefficient Deff and color change index increased with the increase in drying temperature. Meanwhile, from 35 °C to 45 °C, the saponin content after drying tended to increase gradually, but when the temperature continued to rise from 45 °C to 55 °C, the saponin content decreased. The effect of ultrasonic power in the drying process was in particular as follows. The drying time of 8.8 h at 40 W ultrasonic power reduced to 7.8 h at 80 W ultrasonic power, and reduced to 7 h at 160 W ultrasonic power. The remaining saponin content after drying tended to increase gradually at the power level of 40–120 W (from 89.2% to 95.2%) and decrease when the power increased from 120 to 160 W (from 95.2% to 90.5%). The moisture diffusion coefficient Deff also increased with the increase in ultrasonic power. Meanwhile, the color change of dried products decreased as the ultrasonic power increased in the range of 40–120 W but increased with the ultrasonic power range from 120 to 160 W. Additionally, the experimental method and Box–Behnken design were used for optimizing the drying process with the optimal drying conditions such as drying air temperature of 45.2 °C, ultrasonic power of 127.7 W and intermittency ratio of ultrasound generator of 0.18.
The main purpose of this study was to select the appropriate ultrasound parameters that support the freezing process of Bo Chinh ginseng. This process involves placing Bo Chinh ginseng in an open-air environment and ensuring that the transducer does not come into contact with the material. The research results show that the ultrasound power, ultrasound irradiation temperature and intermittency ratio all affect the freezing time, nucleation temperature, color and microstructure of the materials. When the ultrasound continuously operated during the freezing process, at a frequency of 20 kHz, there was a 29.1% reduction in the freezing time at a power level of 100 W as compared to freezing without the help of ultrasound irradiation. The irradiation temperature and nucleation temperature have a linear relationship () which can help to control the nucleation temperature, thereby changing the ice crystal size. Ultrasound-assisted freezing at a 0.6 intermittency ratio had the shortest freezing time. The microstructure of the material changed after ultrasound-assisted freezing and many microchannels and holes were generated. When frozen at a wave rate of 0.4, the microchannels that were created in the material effectively supported the process of water drainage in the drying sublimation stage. At the same time, ultrasound irradiation did not affect the color of the post-freezing material when compared to the color of the frozen material that did not undergo ultrasound irradiation.
This study focused on an engineering problem of heat and mass transfer in infrared (IR) assisted heat pump (HP) drying of purple yam including both a drying experiment and theory of heat and mass transfer mathematical equations. The experimental drying of yam by the IR assisted HP drying method was performed to evaluate the effect of IR power on drying rate and heating rate. The input drying parameters included the drying air temperature of 50°C, drying air velocity of 2.5 m·s −1 and IR power of 0, 300 and 350 W, in which, at the IR power of 0 W, the HP-only drying mode was performed. The experimental drying results showed that the IR assisted HP drying method could improve the drying rate and heating rate as compared to HP-only drying. At the IR power of 350 W, the drying time was the shortest (150 minutes), followed by the IR power of 300 W (210 minutes) and HP-only drying (300 minutes). The IR assisted HP drying obtained the high heating rate as the time required for the drying material to reach the drying temperature was about 35 and 25 minutes corresponding to the IR power of 300 and 350 W. While in HP-only drying, it took about 270 minutes for the drying material’s temperature to reach nearly the drying air temperature value. Besides, the comparison between the predicted data by numerically solving the heat and mass transfer equations and experimental drying data was also conducted. The analysis results indicated that the predicted data could be used to predict the experimental data accurately. The theoretical results of heat and mass transfer in the IR assisted HP drying process as well as experimental drying results would be the basis for improving the IR assisted HP drying equipment to achieve the drying efficiency including the drying rate, quality of dried products, and energy consumption.
A radio-frequency (RF) generator applied in drying technology was designed and manufactured for drying Ganoderma lucidum. The drying experiments were conducted by drying method of RF-assisted heat pump in order to inspect the operating parameters of the RF generator and investigate the effects of the input drying parameters on drying rate in the RF-assisted heat pump drying of Ganoderma lucidum. The results have shown that the RF generator achieved the required operating parameters as design such as RF power of 3 kW and operating frequency of 27 MHz. In RF-assisted heat pump drying, increase in RF power and drying air temperature increases the drying rate. Meanwhile, drying air velocity does not significantly affect the drying rate. At RF power of 1.95 kW, the drying time reduces by 9, 17, and 33% in comparison with RF power of 1.3, 0.65, and 0 kW (heat pump drying). At drying air temperature of 50°C, the drying time reduces by 10% and 21% in comparison with drying air temperature of 40 and 45°C. Besides, increasing RF power retains the higher content of polysaccharide in Ganoderma lucidum, and the Ganoderma lucidum samples retain the color better after drying.
This study focused on the thin-layer drying of yam by infrared-assisted heat pump drying to determine the thin-layer drying model, the effective moisture diffusivity, and the activation energy of moisture within the yam. The thin-layer drying experiment was conducted with input drying parameters such as drying temperatures of 40, 45, and 50°C, drying air velocity of 2.5 m·s⁻¹, and infrared power of 250, 300, and 350 W. In order to determine a suitable thin-layer drying model for describing the yam drying process, six different thin-layer drying models (Lewis, Page, Modified Page, Henderson and Pabis, Wang and Singh, and Midilli) were chosen for nonlinear regression with the experimental drying data. The Midilli model was found to be the most suitable drying model for describing the thin-layer drying of yam. The average effective moisture diffusivity was in the range of 4.184×10⁻⁹ to 8.142×10⁻⁹ m²·s⁻¹, and the activation energy was in the range of 16.78 to 21.01 kJ·mol⁻¹ over the proposed range of drying input parameters